Results 11 to 20 of 42
Thread: Pegasus 12" Build Notes
Hybrid View
-
09-21-2016, 12:24 PM #1
- Join Date
- Aug 2016
- Location
- Raleigh, NC
- Posts
- 13
Hello,
I am slowly progressing through my build. I am attaching the y extrusion to the frame and they never seem to get tight. It says to make sure that they are level with the bottom of the bracket, but when I try to tighten, they rotate and move all around and never seem to get tight. Any thoughts?
-
09-21-2016, 03:28 PM #2
- Join Date
- Jul 2014
- Posts
- 305
-
09-21-2016, 03:32 PM #3
- Join Date
- Aug 2016
- Location
- Raleigh, NC
- Posts
- 13
-
09-21-2016, 03:37 PM #4
- Join Date
- Jul 2014
- Posts
- 305
-
09-21-2016, 04:00 PM #5
- Join Date
- Aug 2016
- Location
- Raleigh, NC
- Posts
- 13
I'll have to purchase the washers too. I am a new guy. I haven't built up a big stock of extra parts yet.
-
09-21-2016, 05:09 PM #6
- Join Date
- Jul 2016
- Location
- Pennsylvania, USA
- Posts
- 255
Hi
If you are using the correct hardware, your extrusions are not tapped deep enough. You can either have Colin swap them out or get a tap and clean up the parts you have. If you have tapped parts before this one is no different. If you have never done it, spend some time with YouTube. There is a bit of a technique to doing it without breaking the tap.
Bob
-
09-21-2016, 06:17 PM #7
- Join Date
- Jul 2016
- Location
- Pennsylvania, USA
- Posts
- 255
Hi
Ok, here's a picture
(image *should* have been here but it isn't ....)
223_ - 1.jpg
It's a shot of the foot I decided to use. I fiddled around a lot and ultimately decided on a pretty simple design.
Let's see if the image goes through or not. The "post image" button didn't seem to do much.... Drag and drop also did not work. Try again with a *really* small file ... finally it works.
Next up is the "custom" bed mount piece
224_ - 1.jpg
That is a bit higher resolution than the first one so this is a bit encouraging. The mount piece lets the heater "float' when there is no glass. Put another way, the clamp holds both the glass and the heater in place. That way as the PCB changes size during warmup, things don't move all over the place.
BobLast edited by uncle_bob; 09-21-2016 at 06:49 PM.
-
09-21-2016, 06:28 PM #8
The board currently defaults to inserting images as thumbnails, which people can click on to enlarge. I realized the other day that in the post edit window, you can over-ride this by double clicking on the image and selecting full-size in the properties window that pops up. Edit your post again and give that a shot.
EDIT: And yeah, the board won't accept the high-res pictures people can get from the phone cameras these days. I usually resize photos down to about 800x600 pixels before uploading.Last edited by printbus; 09-21-2016 at 06:45 PM.
-
09-21-2016, 06:50 PM #9
- Join Date
- Jul 2016
- Location
- Pennsylvania, USA
- Posts
- 255
-
09-21-2016, 07:24 PM #10
- Join Date
- Jul 2014
- Posts
- 305
Please explain to me how to...
Yesterday, 12:15 PM in 3D Printer Parts, Filament & Materials