Close
Page 1 of 18 12311 ... LastLast
Threads 1 to 20 of 343

Forum: RepRap Format Printer Forum

Discussion related to RepRap Format 3D Printers.

Sub-Forums Last Post

  1. Discussion related to Firmware Enhancements to Marlin.

    Forum Actions:

    Forum Statistics:

    • Threads: 33
    • Posts: 1,244
  2. Discuss related to Geetech 3D Printers

    Forum Actions:

    Forum Statistics:

    • Threads: 2
    • Posts: 10
  3. Discussion related to MakerFarm Prusa and PrintrBot 3D printers

    Forum Actions:

    Forum Statistics:

    • Threads: 758
    • Posts: 10,134
  1. Sticky Thread Sticky: RepRap Community - Introduce Yourselves

    Started by Eddie, 10-08-2013 12:34 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 63
    • Views: 24,408
    06-22-2016, 11:50 PM Go to last post
  2. Sticky Thread Sticky: Show your RepRap Printers

    Started by Larry, 10-09-2013 09:06 AM
    6 Pages
    1 2 3 ... 6
    • Replies: 54
    • Views: 27,048
    04-05-2016, 06:06 AM Go to last post
    • Replies: 0
    • Views: 183
    07-22-2016, 03:55 AM Go to last post
    • Replies: 0
    • Views: 125
    07-19-2016, 09:39 PM Go to last post
  1. converting to different filament diameter

    Started by ohms, 07-19-2016 07:42 PM
    convert, extruder, filament, hotend, modifications
    • Replies: 1
    • Views: 83
    07-19-2016, 08:38 PM Go to last post
  2. auto leveling crashes into bed after probing

    Started by hegel, 07-03-2016 01:06 AM
    • Replies: 3
    • Views: 225
    07-13-2016, 12:13 PM Go to last post
  3. Angry Ramps 1.4 on Wanhao I3 thermocouple reading

    Started by Goderfer, 07-12-2016 02:26 PM
    ad597, electrical noise, problem, thermocouple, wanhao i3
    • Replies: 2
    • Views: 150
    07-12-2016, 04:31 PM Go to last post
  4. Ramps 1.4 - Swapping Hotend and Heatbed relays

    Started by hernejj, 05-25-2016 06:46 PM
    • Replies: 1
    • Views: 256
    07-07-2016, 02:33 PM Go to last post
  5. Question for Stepper Motor Experts

    Started by Roxy, 06-27-2016 02:56 PM
    • Replies: 4
    • Views: 326
    07-07-2016, 02:29 PM Go to last post
  6. I have just put together my Hictop Prusa i3

    Started by Ray_, 06-28-2016 06:49 AM
    adding dual extruders i3
    • Replies: 1
    • Views: 209
    06-28-2016, 11:21 AM Go to last post
    • Replies: 4
    • Views: 431
    06-20-2016, 10:17 PM Go to last post
  7. Exclamation x homing in wrong direction

    Started by bzmotoninja83, 06-08-2016 02:15 AM
    • Replies: 1
    • Views: 340
    06-18-2016, 01:31 AM Go to last post
    • Replies: 6
    • Views: 615
    06-16-2016, 01:53 AM Go to last post
    • Replies: 0
    • Views: 306
    06-15-2016, 06:13 PM Go to last post
  8. Need Recommendations for a simple non-contact Z-Axis probe

    Started by Roxy, 05-03-2016 05:41 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 1,138
    06-07-2016, 01:56 AM Go to last post
  9. RUMBA / MARLIN / Proximity Sensor

    Started by scalci, 06-01-2016 11:58 AM
    • Replies: 1
    • Views: 204
    06-05-2016, 09:39 AM Go to last post
  10. Sneak peek of my new printer

    Started by CaptainObvious, 04-30-2016 11:22 PM
    • Replies: 6
    • Views: 666
    05-31-2016, 12:41 PM Go to last post
  11. Question Which Control Board to Buy!? Too many choices!

    Started by dvseliteus, 04-28-2016 11:53 AM
    • Replies: 5
    • Views: 758
    05-29-2016, 04:45 PM Go to last post
  12. New guy here

    Started by bzmotoninja83, 04-20-2016 02:42 AM
    2 Pages
    1 2
    • Replies: 16
    • Views: 1,101
    05-29-2016, 12:57 AM Go to last post
  13. E3D installed in an unknown printer

    Started by wjuniorbr, 05-24-2016 09:54 PM
    • Replies: 2
    • Views: 318
    05-27-2016, 12:51 AM Go to last post
  14. Marlin Team Request you do a 1 minute survey!

    Started by Roxy, 05-24-2016 10:36 AM
    • Replies: 0
    • Views: 199
    05-24-2016, 10:36 AM Go to last post
    • Replies: 0
    • Views: 166
    05-23-2016, 05:40 AM Go to last post

Page 1 of 18 12311 ... LastLast

Forum Information and Options

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •