Close



Page 1 of 42 12311 ... LastLast
Threads 1 to 20 of 837

Forum: FlashForge Forum

Discussion of FlashForge 3D Printers.

  1. Lightbulb Sticky Thread Sticky: Flashforge 3D Creator forum.

    Started by Geoff, 11-12-2013 02:33 AM
    32 Pages
    1 2 3 ... 32
    • Replies: 312
    • Views: 255,179
    01-20-2017, 06:26 AM Go to last post
  2. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 03:29 AM
    • Replies: 6
    • Views: 5,699
    10-14-2016, 09:13 PM Go to last post
  3. Sticky Thread Sticky: Flashforge Creator Dual / Pro How to fix Dual Extruders dragging across prints.

    Started by Geoff, 03-23-2014 10:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 102
    • Views: 82,700
    08-29-2016, 02:05 AM Go to last post
  4. Sticky Thread Sticky: Makerware 2.4.0.14 Download (x64)

    Started by Geoff, 10-27-2014 06:24 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 19,552
    11-16-2015, 12:19 AM Go to last post
  1. Powerspec Ultra 3D Prints are leaning in the -X direction

    Started by hayward3, 01-13-2017 03:06 PM
    2 Pages
    1 2
    • Replies: 16
    • Views: 560
    Yesterday, 07:52 AM Go to last post
  2. Problems with my PowerSpec Ultra 3D printer?

    Started by jeffmorris, 12-30-2016 07:11 PM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 1,020
    01-14-2017, 08:47 PM Go to last post
  3. Bought new PowerSpec 3D Pro 2 printer

    Started by jeffmorris, 01-10-2017 08:47 PM
    • Replies: 5
    • Views: 403
    01-13-2017, 09:53 AM Go to last post
    • Replies: 6
    • Views: 348
    01-10-2017, 02:10 PM Go to last post
    • Replies: 4
    • Views: 267
    01-10-2017, 12:43 PM Go to last post
  4. Dreamer SD card issues

    Started by roykirk, 01-07-2017 01:05 AM
    • Replies: 3
    • Views: 325
    01-09-2017, 02:32 PM Go to last post
  5. Flashforge Finder makes bang and bad offset

    Started by tnterps, 01-06-2017 04:04 PM
    finder, flashforge 3d printer, flashforge finder, stepper motor
    • Replies: 1
    • Views: 183
    01-07-2017, 12:23 PM Go to last post
  6. creator pro 2016 help needed please

    Started by huntleybill, 09-09-2016 08:56 PM
    5 Pages
    1 2 3 ... 5
    • Replies: 41
    • Views: 4,075
    01-05-2017, 08:43 AM Go to last post
  7. Unhappy FlashPrint - Raft missing, printing in air

    Started by sira75, 01-04-2017 01:50 PM
    • Replies: 7
    • Views: 345
    01-04-2017, 08:55 PM Go to last post
    • Replies: 7
    • Views: 306
    01-04-2017, 01:19 PM Go to last post
  8. Strange issue with fan control -

    Started by Sam Staton, 12-30-2016 09:14 AM
    • Replies: 3
    • Views: 265
    12-30-2016, 10:37 AM Go to last post
  9. Both Extruders Now Malfunctioned

    Started by Ward, 12-21-2016 06:48 PM
    • Replies: 6
    • Views: 425
    12-28-2016, 08:50 AM Go to last post
    • Replies: 1
    • Views: 223
    12-25-2016, 10:21 AM Go to last post
  10. New to 3d printing, already damaged heat plate

    Started by subzero3, 12-14-2016 11:56 AM
    • Replies: 7
    • Views: 578
    12-24-2016, 11:51 AM Go to last post
  11. FFCP 2016 bed leveling question

    Started by huntleybill, 09-17-2016 09:23 PM
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 2,305
    12-19-2016, 12:27 PM Go to last post
  12. Extrusion issues

    Started by Todd-67, 12-14-2016 01:50 PM
    • Replies: 6
    • Views: 460
    12-15-2016, 02:39 PM Go to last post
  13. Unhappy Huge carriage sag (>>0.2mm)

    Started by namronb, 11-27-2016 04:00 PM
    • Replies: 2
    • Views: 452
    11-28-2016, 08:33 AM Go to last post
  14. Can I use Makerware 3.10 with my FF Creator Pro

    Started by thebomb, 11-21-2016 03:16 PM
    • Replies: 4
    • Views: 596
    11-22-2016, 06:45 AM Go to last post
  15. Scale Factor when using MakeBot Software

    Started by jbresner, 11-21-2016 01:17 PM
    • Replies: 0
    • Views: 238
    11-21-2016, 01:17 PM Go to last post
  16. Use Slic3r with a Flashforge Creator Pro

    Started by wirlybird, 11-12-2016 06:58 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 1,138
    11-21-2016, 12:21 PM Go to last post

Page 1 of 42 12311 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •