Close



Page 1 of 2 12 LastLast
Threads 1 to 20 of 26

Forum: 3D Printing Slicer Discussion

Discuss the various 3D Printing Slicer Software

  1. Sticky Thread Sticky: List of available slicers

    Started by Sebastian Finke, 10-18-2016 05:06 PM
    • Replies: 9
    • Views: 3,080
    11-04-2016, 08:43 AM Go to last post
  1. Cura 15.0.4.6 end code question, bed never homes

    Started by TTVert, 02-21-2017 11:23 PM
    • Replies: 2
    • Views: 799
    08-15-2017, 10:34 PM Go to last post
    • Replies: 0
    • Views: 183
    08-11-2017, 10:20 PM Go to last post
  2. intermittent overextrusion

    Started by Nepherael, 07-21-2017 02:48 PM
    5 Pages
    1 2 3 ... 5
    • Replies: 46
    • Views: 1,634
    07-28-2017, 02:14 PM Go to last post
  3. SelfCAD Settings for a newb

    Started by jg613, 01-24-2017 08:22 AM
    beginer, selfcad
    • Replies: 2
    • Views: 1,530
    07-11-2017, 06:52 AM Go to last post
  4. "3D Printing Failures" book

    Started by jeffmorris, 06-16-2017 07:59 PM
    • Replies: 3
    • Views: 877
    06-17-2017, 11:54 AM Go to last post
  5. Simplify3d--Comes with 2 Licenses?

    Started by number40Fan, 06-10-2017 05:32 PM
    • Replies: 1
    • Views: 401
    06-12-2017, 06:03 AM Go to last post
  6. Question Cura help

    Started by 1-3-2-4, 06-03-2017 01:00 AM
    • Replies: 1
    • Views: 538
    06-03-2017, 04:54 AM Go to last post
  7. Cool Cura Or Simplify3d?

    Started by Labbo1979, 04-29-2017 08:36 PM
    cura, simplify3d, ultimaker
    • Replies: 2
    • Views: 1,018
    05-02-2017, 02:51 AM Go to last post
    • Replies: 5
    • Views: 1,298
    04-20-2017, 01:23 PM Go to last post
  8. Turn LEDs on or off in S3D software?

    Started by jeffmorris, 03-29-2017 03:02 PM
    • Replies: 6
    • Views: 1,416
    04-12-2017, 10:16 PM Go to last post
  9. using supports/rafts help in cura

    Started by akracer, 03-25-2017 04:41 PM
    • Replies: 0
    • Views: 608
    03-25-2017, 04:41 PM Go to last post
  10. Angry Trouble slicing large stl file

    Started by adamrodgers, 03-13-2017 05:37 PM
    • Replies: 3
    • Views: 1,151
    03-23-2017, 07:01 AM Go to last post
  11. Makerware setting

    Started by Kokobi, 03-11-2017 09:29 PM
    • Replies: 1
    • Views: 741
    03-12-2017, 07:12 PM Go to last post
    • Replies: 0
    • Views: 1,012
    02-27-2017, 10:52 PM Go to last post
  12. Slicer Settings for easy to remove supports

    Started by pochrist, 12-18-2016 08:03 PM
    • Replies: 5
    • Views: 1,892
    01-25-2017, 04:08 AM Go to last post
  13. 100% infill and simplify3d.

    Started by curious aardvark, 01-17-2017 06:14 AM
    • Replies: 2
    • Views: 1,287
    01-18-2017, 06:51 AM Go to last post
    • Replies: 2
    • Views: 1,546
    12-28-2016, 02:09 PM Go to last post
  14. Simplify3D

    Started by LambdaFF, 04-07-2014 03:09 PM
    4 Pages
    1 2 3 ... 4
    simplify3d ; soft
    • Replies: 36
    • Views: 15,246
    12-22-2016, 10:37 PM Go to last post
  15. Can't open file from SD card

    Started by jeffmorris, 12-16-2016 07:50 PM
    • Replies: 1
    • Views: 997
    12-17-2016, 11:24 AM Go to last post
  16. Can't convert my STL to Gcode

    Started by rodneumann, 12-11-2016 10:42 PM
    • Replies: 9
    • Views: 3,012
    12-13-2016, 02:29 PM Go to last post

Page 1 of 2 12 LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •