Close
Page 1 of 30 12311 ... LastLast
Threads 1 to 20 of 586

Forum: MakerFarm Forum

Discussion related to MakerFarm Prusa and PrintrBot 3D printers

  1. Sticky Thread Sticky: Show your MODS

    Started by RobH2, 08-07-2014 04:40 PM
    16 Pages
    1 2 3 ... 16
    • Replies: 152
    • Views: 23,925
    05-11-2015, 12:37 PM Go to last post
  2. Lightbulb Sticky Thread Sticky: Makerfarm Calibration Thread of Grand Proportions

    Started by gmay3, 07-16-2014 08:11 AM
    3 Pages
    1 2 3
    • Replies: 26
    • Views: 8,541
    04-17-2015, 04:03 PM Go to last post
  3. Sticky Thread Sticky: Maintenance, Mods and Tips'n'Tricks - Prusa i3

    Started by old man emu, 11-02-2014 12:01 AM
    • Replies: 5
    • Views: 3,624
    11-12-2014, 07:24 AM Go to last post
  1. Bonded Heat bed for 12"

    Started by Chadd, 08-20-2015 01:03 AM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 358
    Today, 02:39 PM Go to last post
  2. Aluminum bed upgrade?

    Started by CoffeeCup, 08-05-2015 07:08 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 679
    Yesterday, 03:50 PM Go to last post
  3. Weird start behavior

    Started by tsteever, Yesterday 10:20 AM
    • Replies: 1
    • Views: 38
    Yesterday, 10:39 AM Go to last post
  4. 10" Regret?

    Started by super fly, 08-24-2015 07:15 PM
    • Replies: 9
    • Views: 218
    Yesterday, 10:05 AM Go to last post
  5. New user needs help!

    Started by spaceorange12, 08-23-2015 10:34 AM
    12", bed, ramps, relay, wiring
    • Replies: 6
    • Views: 171
    08-23-2015, 07:58 PM Go to last post
  6. Davinci JR vs Makerfarm..

    Started by Chadd, 08-22-2015 11:36 PM
    • Replies: 0
    • Views: 110
    08-22-2015, 11:36 PM Go to last post
  7. Help me understand the Acceleration settings

    Started by tsteever, 08-19-2015 02:44 PM
    • Replies: 3
    • Views: 131
    08-19-2015, 07:05 PM Go to last post
  8. Slic3r 1.1.7 vs 1.2.9...

    Started by lakester, 08-17-2015 08:01 PM
    • Replies: 7
    • Views: 230
    08-19-2015, 01:23 PM Go to last post
  9. Not your typical 3mm vs 1.75 question

    Started by tsteever, 08-03-2015 11:31 PM
    • Replies: 5
    • Views: 290
    08-17-2015, 12:25 PM Go to last post
  10. Selling Makerfarm Prua i3v?

    Started by cjalas, 08-16-2015 02:01 AM
    • Replies: 3
    • Views: 217
    08-17-2015, 12:23 PM Go to last post
  11. Stream of I3V 12" Build Consciousness

    Started by lakester, 04-24-2015 12:35 PM
    9 Pages
    1 2 3 ... 9
    • Replies: 82
    • Views: 5,119
    08-15-2015, 05:37 PM Go to last post
  12. Setting up Cura for i3v

    Started by CoffeeCup, 08-13-2015 12:40 AM
    • Replies: 5
    • Views: 224
    08-15-2015, 11:54 AM Go to last post
  13. Something is messing up my esteps!

    Started by tsteever, 08-11-2015 11:51 PM
    • Replies: 6
    • Views: 245
    08-15-2015, 09:20 AM Go to last post
  14. i3v Cura settings

    Started by dacb, 09-04-2014 12:02 AM
    2 Pages
    1 2
    • Replies: 11
    • Views: 4,008
    08-13-2015, 12:05 PM Go to last post
  15. Parametric Coupler for various shaft sizes

    Started by PyramidDave, 08-11-2015 06:28 PM
    • Replies: 0
    • Views: 121
    08-11-2015, 06:28 PM Go to last post
  16. ABS Printing Temp with E3D V6

    Started by CoffeeCup, 08-11-2015 10:15 AM
    • Replies: 3
    • Views: 182
    08-11-2015, 04:57 PM Go to last post
  17. Retraction and Firmware Help

    Started by BLKKROW, 08-10-2015 06:34 PM
    • Replies: 3
    • Views: 191
    08-11-2015, 09:49 AM Go to last post
  18. Heated Bed wiring meltdown

    Started by adamfilip, 02-14-2015 08:23 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 38
    • Views: 4,225
    08-10-2015, 05:08 PM Go to last post
  19. Heads up!!

    Started by Nihonddd, 08-10-2015 02:26 AM
    • Replies: 0
    • Views: 181
    08-10-2015, 02:26 AM Go to last post
  20. Filament jams after slow layer

    Started by tsteever, 08-07-2015 01:44 PM
    • Replies: 3
    • Views: 221
    08-09-2015, 12:12 AM Go to last post

Page 1 of 30 12311 ... LastLast

Forum Information and Options

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •