Results 31 to 40 of 62
Thread: Show your RepRap Printers
Hybrid View
-
03-20-2014, 02:23 PM #1
- Join Date
- Mar 2014
- Location
- Vienna
- Posts
- 47
A lot of great stuff here!
Thats mine: Prusa i3XL with some modifications, but still work in progress.
Prusa i3XL.jpgL1010658.jpg
L1010665.jpgLast edited by ciutateivissa; 09-13-2017 at 09:35 AM.
-
03-25-2014, 10:19 AM #2
OMG!!! I am super jealous now, that is a very nice, clean Prusa i3!!! My next build is going to be a oversized mendel90, will keep ya posted here! Thanks for showing us your printer, really great work!
-
05-15-2014, 03:07 AM #3
Am I the only one here using a RepRapPro Ormerod? ;)
2014-05-13 20.57.20.jpg 2014-05-13 20.57.03.jpg
It has some key bits replaced from stock:
- Different fan duct ("BigBlue360")
- Aluminium bed support
- dc42's improved IR sensor
- Better PSU (Corsair CX430M)
- Various printed upgrades
Also hooked up to a little wireless bridge thingy so I can put it out of the way when printing (currently sitting on the kitchen table).
-
05-22-2014, 04:45 AM #4
- Join Date
- May 2014
- Location
- Belgium
- Posts
- 15
Hello,
I'm using a K8200 from Velleman. Aka 3Drag:
1510982_10202852992957427_5815045185779230447_n.jpg10172627_10202801188942359_7215219541063713656_n.jpg1979751_10202810789462366_2327337408245555643_n.jpg
I have modified it for better quality. Started with printing ABS last week with quite some satisfying results so far.
Btw the eifeltower is printer in 9 pieces ^^
-
06-04-2014, 11:34 AM #5
Here is a picture of my son's printer bench. I know there is room there for at least one more printer? But I am sworn to secrecy for now.
-
08-31-2014, 11:52 AM #6
-
06-02-2015, 10:07 AM #7
- Join Date
- May 2015
- Posts
- 49
Can anyone identify my new, used printer
I just purchased a used Prusa i3 which seems to be working for the most part. Previous owner was not the original, and doesn't know details about it. But I want to identify it. There is no maker information on the frame (I believe it is acrylic, not metal or wood). It uses a RAMPS 1.4 board. Can anyone identify it?
Here's why I'm asking: I want to update the firmware to support an LCD display, and also in case something goes up in smoke, I want to be able to get it going again. I have a new Arduino Mega and RAMPS board, and I want to load them with test firmware and use them as the testbed (so I don't screw up the working boards).
Is there a standard firmware download for these boards and this printer configuration, or do I need to start from scratch? Where can I find firmware to load for this printer, and if possible a configuration that might match? Thanks
Printer photos:
-
06-02-2015, 03:22 PM #8
Could also be the original owner built it from individual parts and not even a kit.
If you can capture the pattern the LEDs on the RAMPS board make at startup in a video, someone might recognize the firmware you currently have. Marlin firmware is probably used on the majority of MEGA2560/RAMPS setups, so that'd be something to look at. There are many sources of info like the RepRap Wiki, youtube, and such that walk through setting up a printer with it. What you'll find with firmware like Marlin is they are very configurable in order to support a very wide range of underlying hardware and applications. The bad side of that is there's a lot of configuration details to understand if you're applying firmware from scratch. What I would probably do is find download files for a Prusa i3 somewhere. They may not be directly useable, but that'd get you closer than if you started with a fresh copy of it. Since I am familiar with the company more than any other, I'd look at the i3 printers at MakerFarm. Download one of their build guides, and watch their videos. The build guide and/or videos will mention where to get firmware for their printer. Download it and review the contents of the configuration.h, configuration_adv.h, and pins.h files at a minimum until you understand them and can figure out where differences need to be made for your printer. If something doesn't make sense, google that parameter label to learn more about that setting. Consider starting a help-needed thread at this forum level and ask questions when you're stuck. Just be prepared to do some of the research on your own - you'll learn the most that way.
-
06-09-2015, 10:09 PM #9
- Join Date
- Apr 2014
- Posts
- 6
Figured here would be a good place for my first post, Here is my current project I call her Fina. No belts ( Lead screws on all axis ) 320x320 Build volume. Almost done. I have to finish setting up software and mount my heatbed and electronics still.
Photo as everyone likes photos.
I also own a Makerfarm Prusa I3V 10" and am already planning a larger Delta build. I also Designed my own prusa Style Machine but have not started to build that one yet. Here is a video over view of it.
-
06-26-2015, 11:24 PM #10
- Join Date
- Dec 2014
- Posts
- 30
i absolutely love that neon green on your machine, Kyo. Looking to purchase a folger prusa i3 kit in the following weeks and I would love it to be in that color.
Last edited by hobbes; 06-27-2015 at 02:43 PM.
Please explain to me how to...
05-17-2024, 12:15 PM in 3D Printer Parts, Filament & Materials