Close



Page 333 of 411 FirstFirst ... 233283323331332333334335343383 ... LastLast
Results 3,321 to 3,330 of 4110
  1. #3321
    Engineer
    Join Date
    May 2016
    Location
    Annapolis, MD
    Posts
    523
    Quote Originally Posted by wirlybird View Post
    All of that time printing and fighting with blower nozzles seems for-not. I installed the single left one and it drags on the bed.
    Maybe loosen the fan and duct, then shift them upward and re-tighten? I wonder if that is how I broke the fan, I tightened it quite a bit...

  2. #3322
    The single I would sand the corner down a bit to give more clearance.
    Or you can slice some off in S3D.

    Quote Originally Posted by wirlybird View Post
    All of that time printing and fighting with blower nozzles seems for-not. I installed the single left one and it drags on the bed.
    Editor in Chief
    Bitsonline

    Tips Appreciated But Not Expected
    BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
    DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq

  3. #3323
    I noticed as well when I installed the dual blower that sits behind there was some jog space in the fan mount itself so I went and held the fan up the highest when I screwed it all in and it gave me extra clearance as well.

    Quote Originally Posted by DaveB View Post
    I wonder what is different? My print of that nozzle does not. As I'd mentioned it was necessary to cut down the length of the flat head wood screw that I used to tie the duct to the clip-on support bracket. The first time I attached it to my QiDi I mounted it incorrectly. The bracket goes on first, then the duct below it.
    Editor in Chief
    Bitsonline

    Tips Appreciated But Not Expected
    BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
    DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq

  4. #3324
    Super Moderator
    Join Date
    Jun 2016
    Location
    Oklahoma
    Posts
    902
    Quote Originally Posted by DaveB View Post
    Maybe loosen the fan and duct, then shift them upward and re-tighten? I wonder if that is how I broke the fan, I tightened it quite a bit...

    I'll look closer at it when the printer is free again. It was really smack on the bed and peeled a print up.

  5. #3325
    I need to get my cable chain printed and built. Every time I see yours I think it looks bad ass. How many links did it need?
    Here is my dual duct setup, I did not use the brace on the right side yet as it pushed it down. Do I am going to fix the groove. I also am going to glue it. I have some plastic weld stuff that will work well. That will get rid of the screw risk.

    Speaking of which does anyone have a good supplier of screws for the different small projects we do with many of these things?

    [IMG] [/IMG]

    Quote Originally Posted by DaveB View Post
    Oops, I had assumed it was the dual that you would have problems with. The left only does not seem to cause me any difficulty. Here is a pix of it in action right now...

    Editor in Chief
    Bitsonline

    Tips Appreciated But Not Expected
    BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
    DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq

  6. #3326
    Super Moderator
    Join Date
    Jun 2016
    Location
    Oklahoma
    Posts
    902
    Looks good. What blue is that? Brand?



    Quote Originally Posted by Talon 3D View Post
    I need to get my cable chain printed and built. Every time I see yours I think it looks bad ass. How many links did it need?
    Here is my dual duct setup, I did not use the brace on the right side yet as it pushed it down. Do I am going to fix the groove. I also am going to glue it. I have some plastic weld stuff that will work well. That will get rid of the screw risk.

    Speaking of which does anyone have a good supplier of screws for the different small projects we do with many of these things?

    [IMG] [/IMG]

  7. #3327
    Engineer
    Join Date
    May 2016
    Location
    Annapolis, MD
    Posts
    523
    Talon:
    Here are some places I have purchased hardware from:

    https://www.amazon.com/gp/product/B014OO5KQG Hilitchi 420pcs M2 M3 Stainless Steel Hex Socket Head Cap Screws Nuts Assortment Kit with Box
    https://www.amazon.com/gp/product/B01GZX9T2U Raogoodcx® 180pcs M4 Stainless Steel Hex Socket Head Cap Screws Nuts Assortment Kit
    https://www.amazon.com/gp/product/B00F33UIJ2 Steel Pan Head Machine Screw, Black Oxide Finish, #2 Phillips Drive, M4-0.7 Thread Size, 10 mm Length, Fully Threaded, Import (Pack of 100)
    https://www.amazon.com/gp/product/B0069TW6DU Tekz 45250 Metric Nut and Bolt Assortment - 475 Piece

    Assorted M3 and M4 hardware from http://stores.ebay.com/afhfasteners/ (Make sure you read the quantity descriptions)

  8. #3328
    Super Moderator
    Join Date
    Jun 2016
    Location
    Oklahoma
    Posts
    902
    Another bad roll from Makergeeks. That's two in a week or so.

  9. #3329
    Engineer
    Join Date
    May 2016
    Location
    Annapolis, MD
    Posts
    523
    Quote Originally Posted by wirlybird View Post
    Another bad roll from Makergeeks. That's two in a week or so.
    That stinks. What color and type? Was it a replacement for a bad roll of the same material?

  10. #3330
    That is the Soultech ABS, here is the link. I really like the color. It does not have quite the stench of some of the other ABS. Really hard as well. Nice to print with.
    https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

    Quote Originally Posted by wirlybird View Post
    Looks good. What blue is that? Brand?
    Editor in Chief
    Bitsonline

    Tips Appreciated But Not Expected
    BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
    DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq

Page 333 of 411 FirstFirst ... 233283323331332333334335343383 ... LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •