Results 191 to 200 of 4110
Thread: Qidi Tech 1 - Replicator 1 clone
-
02-19-2016, 07:40 AM #191
The high lubricity coating slows down wear caused by some of the more exotic filaments and seem to cleanup easier when a print goes bad.
I'm sure the Maghold build plate system works great but I can buy 2 Heat-Resistant Borosilicate Glass, 1/4" Thick, 9" X 6" for less then $45 shipped from
MC-Master-Carr. The ends are polished so there are no sharp edges.
I have 2 printers with four interchangeable glass build plates.
Both systems are proven and work.
-
02-19-2016, 08:56 AM #192
- Join Date
- Jan 2016
- Posts
- 81
I have no doubt they work well!! I just love the simplicity of magnets. Plus you know, MAGNETS!!! Everything is better with magnets!!!!!
And once you have the build plate, the extra plates are like 12$ a pop, so in theory you can get several of them shipped for under $45. :P (J/K)
Both are viable options, I am just not a fan of having clamps/adapters/bed plate holder downer things to mess with when removing plates.
I had a Glass plate set up on my last printer with binder clips. Worked great, except for when I would screw up and put the clips in the wrong place lol.
Regardless of what you go with (Newbie) get something that allows you to remove the build plate, as pulling/pushing/wrenching on the plate while attached will mean you are ALWAYS having to re-level the build plate with nearly every print.
***** Edit: Also with the MagHold plate you gain an extra 4mm of build volume, rather than losing that 1/4" (Not that it is really any serious amount either way lol.)
-
02-19-2016, 02:25 PM #193
- Join Date
- Feb 2016
- Posts
- 11
Has anyone ever seen a magnetic glass build plate?
Does anyone know if a larger build plate could be used to allow a larger object to be printed?Last edited by TankCmdr; 02-19-2016 at 08:33 PM.
-
02-20-2016, 12:11 PM #194
- Join Date
- Nov 2015
- Posts
- 43
You would go with that upgrade versus the upgrade for the Makerbot replicator 1 or 2 for this QidiTech? http://www.micro-swiss.com/#!product...a-909d18850eef
Is that because the Makerbot Replicator 1 or 2 actually use MK8 extruders and the QidiTech used MK10?
-
02-20-2016, 07:36 PM #195
- Join Date
- Feb 2016
- Posts
- 360
I just purchased Simplify3D, doing the initial set up. Its asking what type printer I have. There is no Qidi-tech option. Should I use 'other' or list it as a FlashForge pro?
So exited, my Qidi printer gets here this coming Thursday. And now that I have S3D gonna be getting a bunch of stuff ready and loaded on SD cards.
-
02-20-2016, 07:44 PM #196
- Join Date
- Nov 2015
- Posts
- 43
-
02-20-2016, 07:45 PM #197
- Join Date
- Nov 2015
- Posts
- 43
-
02-20-2016, 08:29 PM #198
- Join Date
- Jan 2016
- Posts
- 81
You need to edit the gcode script for start something like this:
G1 X-130 Y-75 Z30 F9000 ; Move to wait position off table G130 X20 Y20 Z20 A20 B20 ; Lower stepper Vrefs while heating
M126 S[fan_speed_pwm] ; Set fan speed
M140 S[bed0_temperature] T0 ; Heat buildplate
M134 T0 ; Stabilize bed temperature
M104 S[extruder1_temperature] T1 ; Heat left extruder
M133 T1 ; Stabilize left extruder temperature
G130 X127 Y127 Z40 A127 B127 ; Default stepper Vrefs
G92 A0 B0 ; Zero extruders
M135 T1 ; Load left extruder offsets
G1 X-100 Y-70 F9000 ; Move to front left corner of bed
G1 Z0.3 F6000 ; Move down to purge
G1 X90 Y-70 E24 F2000 ; Extrude a line of filament across the front edge of the bed
G1 X100 Y-7 F180 ; Wait for ooze
G1 X110 Y-70 F5000 ; Fast wipe
G1 Z1 F100 ; Lift
G92 A0 B0 ; zero extruders
That will produce a long line across the front of the bed rather than a glob.
-
02-20-2016, 08:34 PM #199
- Join Date
- Nov 2015
- Posts
- 43
-
02-20-2016, 10:37 PM #200
- Join Date
- Jan 2016
- Posts
- 81
What I did was copied the start gcode from the replicator 2x profile and pasted it into the start code for the flashforge pro
Qidi X Plus 3 Paper thin first...
Yesterday, 01:15 AM in General 3D Printing Discussion