Results 2,851 to 2,860 of 4110
Thread: Qidi Tech 1 - Replicator 1 clone
-
08-18-2016, 11:36 AM #2851
- Join Date
- Feb 2016
- Posts
- 360
Nope, not yet. Really only outlet I have to do so is local classifieds like G-list and letgo. And not in a good area to sell something like this. Guess I could post it online somewhere (though past ebay I wouldn't know where) but the shipping is killer. I need at least $600 out of it to get done what I wanna do. Plus would need another $100 for shipping it (did the USPS shipping calculator and it said $82, plus box+foam n stuff). I just don't see someone wanting to pay $700 for 6 month old one when new ones are $700-$800 brand new. But I can hope lol.....
It has been working just fine though...still no clue what was going on those few days.
Still stuck to right side only though...I need to take apart left side so I can clean the hotblock from a misprint that causes a material buildup all over the hotblock.
-
08-18-2016, 11:46 AM #2852
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
Yeah, that's a hard $ nut to crack. I am still adding gilding onto my fuzzy dice here. I keep trying to come up with a reason to add lasers in there too (I still like lasers). But I can't think of any purpose they would serve other than to look really wicked.
By the way, if you have the time could you post a pix of your left side hotblock? I am curious to see what I am sure I will someday run into and have to deal with.
-
08-18-2016, 01:47 PM #2853
- Join Date
- Feb 2016
- Posts
- 360
-
08-18-2016, 04:11 PM #2854
Looking at the right nozzle and how it is installed I am betting the left just needs to be reset like I outlined a few days ago. First, fully seat the thermal tube into the heater block. Then tighten the nozzle into that. If you can use a little longer PTFE with the inside diameter chamfered a little.
I would do it to the right side while you are at it.
-
08-18-2016, 05:44 PM #2855
- Join Date
- Jun 2016
- Location
- Oklahoma
- Posts
- 904
New issue. These used to print great but I can't seem to get the settings correct. This is a very small part.
1. The blobs on the side. This is where each layer starts. I can watch plop out a big blob of plastic as the extruder starts to move. Odd also that it doesn't start until several layers have printed.
2. The first layers are undersized in diameter. You can see how it slopes out as you go up in height.
-
08-18-2016, 06:00 PM #2856
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
-
08-18-2016, 06:25 PM #2857
- Join Date
- Jun 2016
- Location
- Oklahoma
- Posts
- 904
Here is another blob issue! This thing has lost its mind!!
It is the corners and seems to be every few layers.
-
08-18-2016, 06:28 PM #2858
- Join Date
- Jun 2016
- Location
- Oklahoma
- Posts
- 904
-
08-18-2016, 07:18 PM #2859
- Join Date
- Feb 2016
- Posts
- 360
The issue with the left side has nothing to do with nozzle or ptfe tube.
What happened was I started a print, and then got busy with the kids. Print didn't stick good, and bunched up on the nozzle. Machine of course kept feeding material till I catch it an hour or so later with a big gob of material around nozzle and hotblock.
-
08-18-2016, 08:25 PM #2860
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
New to 3d printing looking for...
05-20-2024, 12:56 AM in Tips, Tricks and Tech Help