Close



Page 1 of 180 1231151101 ... LastLast
Threads 1 to 20 of 3595

Forum: General 3D Printing Discussion

Anything Related to the 3D Printing Industry which doesn't belong in the our other folders goes here.

    • Replies: 18
    • Views: 19,273
    03-27-2021, 02:20 AM Go to last post
  1. Sticky Thread Sticky: Technical Information Resources

    Started by Ward, 11-23-2015 09:37 AM
    • Replies: 9
    • Views: 25,978
    03-26-2021, 01:26 AM Go to last post
  2. Question Sticky Thread Sticky: Best 3D printer for me? Comment advice.

    Started by Ben2900, 04-26-2017 08:44 AM
    10 Pages
    1 2 3 ... 10
    • Replies: 98
    • Views: 74,242
    02-25-2021, 03:13 AM Go to last post
  3. Sticky Thread Sticky: FDM Material/plastics Guide From Simplify3d

    Started by curious aardvark, 01-11-2021 10:00 AM
    • Replies: 0
    • Views: 2,218
    01-11-2021, 10:00 AM Go to last post
  4. Sticky Thread Sticky: Printing anti-droplet face shields.

    Started by PPEprinter, 04-01-2020 02:13 AM
    • Replies: 8
    • Views: 7,549
    07-21-2020, 04:32 AM Go to last post
  1. Slicers and Print Speeds

    Started by sonnichs, 04-07-2021 08:22 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 366
    Today, 06:51 AM Go to last post
    • Replies: 3
    • Views: 3,400
    Today, 04:04 AM Go to last post
  2. Check this App development services

    Started by jonny2113, Yesterday 05:30 PM
    • Replies: 0
    • Views: 80
    Yesterday, 05:30 PM Go to last post
  3. Top Surface Roof layer is really rough

    Started by Gamble, 07-16-2015 09:39 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 4,702
    04-09-2021, 09:06 AM Go to last post
  4. Lightbulb Needing some help on a project.

    Started by Sam .C, 04-07-2021 07:44 AM
    • Replies: 3
    • Views: 146
    04-07-2021, 07:19 PM Go to last post
  5. When to use 'Support' option?

    Started by terrypin, 04-04-2021 01:42 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 454
    04-07-2021, 12:39 PM Go to last post
  6. Screw Holes and Solid Infill

    Started by sonnichs, 03-28-2021 10:51 PM
    3 Pages
    1 2 3
    • Replies: 26
    • Views: 929
    04-06-2021, 12:20 PM Go to last post
    • Replies: 2
    • Views: 1,466
    04-06-2021, 05:31 AM Go to last post
  7. Printed part does not stick on the heated bed

    Started by emilytako, 01-08-2020 07:43 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 3,108
    04-06-2021, 02:07 AM Go to last post
    • Replies: 9
    • Views: 585
    04-05-2021, 07:36 AM Go to last post
  8. creality ender 3 v2 weird layer separation

    Started by Lazingo, 04-03-2021 03:11 PM
    • Replies: 0
    • Views: 176
    04-03-2021, 03:11 PM Go to last post
  9. Best Material For A Bird Fountain?

    Started by davidhunternyc, 03-23-2020 12:47 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 3,576
    04-03-2021, 05:54 AM Go to last post
    • Replies: 3
    • Views: 265
    04-03-2021, 12:36 AM Go to last post
  10. Should I terminate this print?

    Started by terrypin, 04-02-2021 06:44 AM
    • Replies: 2
    • Views: 188
    04-02-2021, 12:16 PM Go to last post
  11. Question Laptop requirements?

    Started by Shieldse, 12-31-2014 03:52 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 21,049
    04-02-2021, 09:03 AM Go to last post
    • Replies: 4
    • Views: 466
    04-01-2021, 05:21 PM Go to last post
  12. Need help- single micron range 3D printing

    Started by elthames, 03-30-2021 10:36 PM
    high resolution, single micron
    • Replies: 5
    • Views: 1,609
    04-01-2021, 09:18 AM Go to last post
  13. not getting the answeer i need

    Started by jamesmatheson, 01-07-2020 04:38 PM
    • Replies: 5
    • Views: 1,450
    04-01-2021, 03:46 AM Go to last post
  14. Thingiverse downloads give security warnings

    Started by terrypin, 03-31-2021 09:57 AM
    • Replies: 0
    • Views: 128
    03-31-2021, 09:57 AM Go to last post
  15. Understanding these parameters?

    Started by terrypin, 03-29-2021 11:33 AM
    • Replies: 3
    • Views: 285
    03-30-2021, 01:48 PM Go to last post

Page 1 of 180 1231151101 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data