Close



Page 1 of 51 12311 ... LastLast
Threads 1 to 20 of 1002

Forum: FlashForge Forum

Discussion of FlashForge 3D Printers.

  1. Lightbulb Sticky Thread Sticky: Flashforge 3D Creator forum.

    Started by Geoff, 11-12-2013 02:33 AM
    33 Pages
    1 2 3 ... 33
    • Replies: 320
    • Views: 559,309
    01-03-2021, 09:24 AM Go to last post
  2. Sticky Thread Sticky: Flashforge Creator Dual / Pro How to fix Dual Extruders dragging across prints.

    Started by Geoff, 03-23-2014 10:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 103
    • Views: 188,517
    12-02-2019, 06:06 AM Go to last post
  3. Sticky Thread Sticky: Makerware 2.4.0.14 Download (x64)

    Started by Geoff, 10-27-2014 06:24 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 68,474
    11-07-2019, 01:23 PM Go to last post
  4. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 03:29 AM
    • Replies: 6
    • Views: 24,811
    10-14-2016, 09:13 PM Go to last post
  1. Adventurer 3 NinjaFlex and FlashPrint

    Started by budmaniac, 01-16-2021 03:59 PM
    adventurer 3, flashprint, ninjaflex
    • Replies: 0
    • Views: 103
    01-16-2021, 03:59 PM Go to last post
  2. Question Flashprint 4.6 issue on Linux (with nVidia)

    Started by kaipee, 01-15-2021 11:25 AM
    flashprint, linux
    • Replies: 0
    • Views: 128
    01-15-2021, 11:25 AM Go to last post
  3. Flashforge Finder Bed Problem

    Started by Raypow, 01-14-2021 06:44 AM
    • Replies: 0
    • Views: 150
    01-14-2021, 06:44 AM Go to last post
  4. Internal SD card dreamer.

    Started by bookworm1707, 01-31-2017 03:21 AM
    • Replies: 3
    • Views: 2,932
    01-13-2021, 03:15 PM Go to last post
  5. Ask anything about the Flashforge Adventurer 3 3D Printer

    Started by Peet@FFUSA, 01-15-2019 11:56 AM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 13,246
    01-13-2021, 04:22 AM Go to last post
  6. Newbie with Flashforge Issues: Help please

    Started by Streetsnake, 01-07-2021 03:25 PM
    • Replies: 1
    • Views: 345
    01-07-2021, 03:32 PM Go to last post
  7. FF Creator 3 first layer adhesion issues

    Started by davaze, 01-03-2021 07:16 AM
    • Replies: 0
    • Views: 284
    01-03-2021, 07:16 AM Go to last post
    • Replies: 0
    • Views: 474
    12-28-2020, 01:54 AM Go to last post
  8. Question Flashforge Creator Pro misalignment

    Started by matteog, 12-23-2020 08:45 AM
    • Replies: 0
    • Views: 639
    12-23-2020, 08:45 AM Go to last post
  9. Creator Pro Fuse?

    Started by jday7757, 12-17-2020 09:02 AM
    • Replies: 0
    • Views: 604
    12-17-2020, 09:02 AM Go to last post
  10. [GUIDER II] Filament sensor hack?

    Started by DaveH, 12-04-2020 06:38 AM
    • Replies: 6
    • Views: 1,612
    12-06-2020, 07:55 AM Go to last post
    • Replies: 7
    • Views: 1,555
    12-05-2020, 12:06 PM Go to last post
    • Replies: 1
    • Views: 845
    12-05-2020, 10:01 AM Go to last post
  11. Flashforge finder problem

    Started by Bad Dog, 08-16-2020 02:14 PM
    • Replies: 1
    • Views: 1,649
    12-04-2020, 07:07 AM Go to last post
  12. Angry Defect when printing with ABS

    Started by gxryy, 11-04-2020 03:54 AM
    • Replies: 2
    • Views: 1,358
    12-04-2020, 04:58 AM Go to last post
  13. Flashforge Creator Pro - Layer Problem

    Started by IanT, 11-20-2020 07:08 AM
    • Replies: 6
    • Views: 1,442
    12-03-2020, 07:45 AM Go to last post
  14. Advice required

    Started by imalc, 12-02-2020 06:46 AM
    • Replies: 2
    • Views: 782
    12-02-2020, 11:36 AM Go to last post
  15. Flashforge guider II s: poor layer adhesion

    Started by pelgrim, 10-17-2020 12:10 PM
    • Replies: 1
    • Views: 2,112
    11-25-2020, 06:07 AM Go to last post
    • Replies: 3
    • Views: 1,415
    11-17-2020, 09:25 AM Go to last post
  16. Older Creater Pro but wont feed in new filiment

    Started by RURC, 10-08-2020 04:25 PM
    • Replies: 5
    • Views: 2,196
    10-16-2020, 11:05 AM Go to last post

Page 1 of 51 12311 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data