Close



Page 11 of 42 FirstFirst ... 91011121321 ... LastLast
Threads 201 to 220 of 832

Forum: MakerFarm Forum

Discussion related to MakerFarm Prusa and PrintrBot 3D printers

  1. Sticky Thread Sticky: Show your MODS

    Started by RobH2, 08-07-2014 04:40 PM
    19 Pages
    1 2 3 ... 19
    • Replies: 188
    • Views: 378,714
    04-16-2024, 07:41 AM Go to last post
  2. Lightbulb Sticky Thread Sticky: Makerfarm Calibration Thread of Grand Proportions

    Started by gmay3, 07-16-2014 08:11 AM
    3 Pages
    1 2 3
    • Replies: 24
    • Views: 138,466
    04-17-2015, 04:03 PM Go to last post
  1. Amazing!

    Started by tonybuckley, 12-17-2015 10:41 AM
    • Replies: 2
    • Views: 3,365
    12-18-2015, 04:54 AM Go to last post
  2. R.I.P. Power Supply

    Started by spaceorange12, 12-08-2015 09:26 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 31
    • Views: 20,717
    12-17-2015, 03:13 PM Go to last post
  3. Plastic Buildup on nozzle exterior

    Started by adamfilip, 12-16-2015 01:10 PM
    • Replies: 7
    • Views: 19,151
    12-16-2015, 09:31 PM Go to last post
  4. Quality issue. Vibration/ringing?

    Started by mattanonymous, 11-25-2015 08:23 AM
    • Replies: 3
    • Views: 3,687
    12-15-2015, 04:34 PM Go to last post
  5. Support with Support

    Started by gmay3, 12-15-2015 04:29 PM
    • Replies: 0
    • Views: 2,475
    12-15-2015, 04:29 PM Go to last post
  6. Experiences with Pegasus?

    Started by BLKKROW, 12-06-2015 05:33 PM
    • Replies: 9
    • Views: 7,744
    12-15-2015, 05:02 AM Go to last post
    • Replies: 2
    • Views: 3,385
    12-14-2015, 05:54 PM Go to last post
  7. RAMPS or RAMBO

    Started by SgtToe, 02-18-2015 11:37 AM
    2 Pages
    1 2
    • Replies: 14
    • Views: 25,827
    12-09-2015, 06:44 AM Go to last post
  8. E3D cyclops?

    Started by Chadd, 12-08-2015 01:12 AM
    • Replies: 0
    • Views: 2,400
    12-08-2015, 01:12 AM Go to last post
  9. Not all Slicers are created equal

    Started by walkercreations, 03-28-2015 09:05 AM
    2 Pages
    1 2
    • Replies: 12
    • Views: 11,768
    12-04-2015, 02:08 PM Go to last post
  10. Noise / EMF Shielding Coil for Steppers

    Started by adamfilip, 11-24-2015 09:04 AM
    • Replies: 3
    • Views: 3,674
    11-28-2015, 04:26 PM Go to last post
  11. What plastic for Printer Parts

    Started by BLKKROW, 10-26-2015 03:40 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 10,670
    11-27-2015, 07:37 AM Go to last post
  12. New Marlin firmware?

    Started by tsteever, 11-19-2015 08:14 AM
    2 Pages
    1 2
    • Replies: 13
    • Views: 11,055
    11-25-2015, 09:53 AM Go to last post
  13. e3d nozzle jam. My fault?

    Started by manianac, 11-22-2015 04:08 PM
    • Replies: 5
    • Views: 4,042
    11-25-2015, 01:15 AM Go to last post
  14. Another "what causes this"

    Started by lovincup, 11-22-2015 05:28 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 8,845
    11-23-2015, 12:22 PM Go to last post
  15. Leaky Hot End

    Started by spaceorange12, 11-20-2015 08:20 PM
    barrel, heat block, hot end, leaking
    • Replies: 6
    • Views: 5,278
    11-22-2015, 08:56 PM Go to last post
  16. Hotend wont heat

    Started by adamfilip, 11-22-2015 04:57 PM
    • Replies: 3
    • Views: 4,589
    11-22-2015, 08:27 PM Go to last post
    • Replies: 2
    • Views: 3,039
    11-20-2015, 08:02 AM Go to last post
  17. New filaments on makerfarms website

    Started by Schnupp, 11-17-2015 07:04 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 8,333
    11-19-2015, 12:06 PM Go to last post
  18. Power issues advice

    Started by usarmyaircav, 11-16-2015 04:14 PM
    • Replies: 5
    • Views: 6,482
    11-16-2015, 09:52 PM Go to last post

Page 11 of 42 FirstFirst ... 91011121321 ... LastLast

Forum Information and Options

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data