Activity Stream
-
Older Activity
-
Today, 08:12 AMI think you could be right about it being silk PLA, I remember reading that as well. I know its not the nozzle, i replaced it recently. I do not know...4 replies | 65 view(s)
-
Today, 08:06 AMSuggestions............ Bowden tube deteriorated at the hot end and not sealing properly or perhaps a partially clogged nozzle. Try a different...4 replies | 65 view(s)
-
Today, 07:22 AMWith all due respect, I have tried different infill settings, up to 100 percent. This issue still crops up. Ill try 20 percent again if you need me...4 replies | 65 view(s)
-
Today, 01:48 AMTry increasing infill to 20%. Hard to see what the actual print is from pic.4 replies | 65 view(s)
-
Yesterday, 11:30 PMI bought this thing about a year ago just to stare at it seems. It's been out of the box, I powered it up like twice, manipulated the print plate,...0 replies | 82 view(s)
-
Yesterday, 10:12 PMHi everyone,I am new to this forum, I just joined today. My name is Jared.I joined because I have an issue with my 3d printer that I cannot seem to...4 replies | 65 view(s)
-
Yesterday, 07:34 PMHey guys. Bambu labs x1 carbon and Bambu PLA cf filament. I dried the filament before hand for 8 hours. The design I’m printing is one I made in...0 replies | 91 view(s)
-
06-09-2024, 02:07 PMJimmyJack121063 replied to a thread Printed Model of Motor Cooling Fan Breaks Apart When Operating in General 3D Printing DiscussionThanks for the info. I am having a printing service print this model in nylon for me and if that one does not hold up I will try the salt annealing...2 replies | 424 view(s)
-
06-09-2024, 10:05 AMfred_dot_u replied to a thread Printed Model of Motor Cooling Fan Breaks Apart When Operating in General 3D Printing DiscussionIt's possible that a nylon version of this fan would hold up better, but nylon can be challenging to print if you are the printing resource. As you...2 replies | 424 view(s)
-
06-08-2024, 11:22 PMHi guys, I own an Ender 3 v2 printer and have recently bought one of the Eclipson airplane models to print on it. I am printing with LW-PLA and...0 replies | 205 view(s)
-
06-08-2024, 08:54 PMJimmyJack121063 started a thread Printed Model of Motor Cooling Fan Breaks Apart When Operating in General 3D Printing DiscussionI had a model maker design an electric air compressor motor cooling fan due to the fact that I broke the original one and they are now obsolete and...2 replies | 424 view(s)
-
06-08-2024, 03:40 PMArticulated magnet: https://cults3d.com/en/3d-model/art/cat-hold-magnet0 replies | 319 view(s)
-
06-06-2024, 05:13 PMhello, do you 3dprint this table with double nozzles priter, or just it 3dprinted whole table and stick to the foil with markers? Which technique...40 replies | 170418 view(s)
-
06-06-2024, 05:09 PMHi All,anybody try to scan markers with Einscan SP? Only 3mm markers can be worked for markers? I stick 0,8mm markers, but the scanner do not...40 replies | 170418 view(s)
-
06-05-2024, 07:31 AMPLAyer_uno started a thread Blue screen of death after thermal runaway - fried motherboard? in General 3D Printing DiscussionHello all, While cleaning the hot end on my Ender 3, with the printer was on and the hot end at 215C, I must have accidentally caused a short...0 replies | 655 view(s)
-
06-04-2024, 09:14 AMBikeracer2020 replied to a thread Holes and pockmarks in print walls in General 3D Printing DiscussionLooks like some under extrusion there. Possibly a gap between the end of the bowden tube and the new nozzle, the bowden tube needs cutting square...1 replies | 622 view(s)
-
06-04-2024, 05:50 AMHello, I'm new to 3d printing and this is my first post here. Recently bought an old Ender 3 with 1 partially used roll and 1 new packaged rool of...1 replies | 622 view(s)
-
06-03-2024, 02:23 PMImpressive articulated amazon parrot by biologist artist Arara on cults: https://cults3d.com/en/3d-model/art/amazon-parrot-articulated-figure0 replies | 849 view(s)
-
06-02-2024, 01:14 PMHi everyone, I'm new to the forum. I have an opportunity to get a pre-owned Lulzbot TAZ Pro. I've been looking online to get an idea of what the...0 replies | 972 view(s)
-
05-31-2024, 04:03 PMAlways encourage everyone to learn the basics of CAD or 3d polygonal modeling to really get the most out of their 3d printer. These fidget ring toys...42 replies | 48073 view(s)
-
05-31-2024, 12:45 PMHello all First post and just looking at getting into 3D printing. Looking into buying a Printer for work purposes as a innovation trial. Budget...0 replies | 894 view(s)
Printed Model of Motor Cooling Fan...
06-09-2024, 02:07 PM in General 3D Printing Discussion