Activity Stream
-
Older Activity
-
Today, 12:56 AMHello everyone, another stretch goal is now unlocked, 19 in total !! Almost 280 stl parts !!16 replies | 5530 view(s)
-
Yesterday, 03:07 PMBikeracer2020 replied to a thread Adventurer 3 filling holes in design! in Tips, Tricks and Tech HelpLoaded your STL into Orca slicer and it appears you have two STL's one on top of the other.1 replies | 181 view(s)
-
Yesterday, 11:53 AMhello, relatively new to 3d printing although i did some at university. I am currently trying to print a speaker grill for my car, however all the...1 replies | 181 view(s)
-
Yesterday, 04:38 AMworld of warcraft or dota15 replies | 18688 view(s)
-
Yesterday, 02:22 AMIt's done ! Another one : Barbarian Saber is now unlocked :)16 replies | 5530 view(s)
-
Yesterday, 12:58 AMHello everyone, one more unlocked Stretch goal : Tomahawk Saber !! The next one is close ! 24 hours left !! Have a fun day ^^16 replies | 5530 view(s)
-
Yesterday, 12:02 AMCongrats on the 1X. I have a P1P and have yet to open a glue stick. The build plate has been awesome all by itself and I have had zero printer...3 replies | 1157 view(s)
-
03-17-2024, 03:11 PMThanks mate, greatly appreciated. I realised I was using too much glue, I decided to try no glue at all and got perfect bed adhesion and didn't face...3 replies | 1157 view(s)
-
03-17-2024, 10:49 AMI just did a quick google for 3d printing bed adhesion issues and this one should answer all your questions ...3 replies | 1157 view(s)
-
03-17-2024, 07:48 AMSo, for anyone also experiencing this issue i found the problem.It was the TMC2208 stepper drivers overheating. I noticed when opining the...1 replies | 760 view(s)
-
03-17-2024, 03:18 AMHello again, another stretch goal just unlocked !! The Old West saber is now available ! Let's have a look at the next one : the Tomahawk Saber !...16 replies | 5530 view(s)
-
03-17-2024, 02:07 AMHello everyone, we are close to the end of the campaign :) NOW YOU CAN GET MORE THAN 260 STL PARTS FOR ONLY 34 EUROS (37 DOLLARS) !!! 15...16 replies | 5530 view(s)
-
03-16-2024, 08:44 PMHi, I have lost the USB connection with the printer. I updated the firmware, and after it loaded, when I try to print through CURA it doesn't...0 replies | 759 view(s)
-
03-16-2024, 07:47 PMatmane.djalil09 started a thread How to change printing parameters for PA6 in 3D Systems SPRO 60 ? in 3D Printers (Hardware)Hello,I am a PhD student working on evaluating the mechanical and geometric quality of parts printed using Selective Laser Sintering,I have already...0 replies | 909 view(s)
-
03-16-2024, 06:56 PMfred_dot_u replied to a thread Help selecting a really good 3D printer for a middle school? in 3D Printers (Hardware)People might consider me to be a Prusa fanboy, but my experience is a few years old. The local public library purchased without advisories a Cube 3...1 replies | 1235 view(s)
-
03-16-2024, 08:47 AMRHg started a thread top surface / layer bad quality Bambu Lab P1S printer in Tips, Tricks and Tech Helphi, my top surfaces went from printing almost perfect like the green circle shows on the below photo to printing rough and scratched top surfaces...0 replies | 935 view(s)
-
03-16-2024, 12:13 AMHello Everyone and thanks for checking out my little start-up QT Bits. QT Bits is a technology company that aims to deliver innovative and unique...0 replies | 546 view(s)
-
03-15-2024, 06:08 PMPete Moss started a thread Help selecting a really good 3D printer for a middle school? in 3D Printers (Hardware)My grandkids are in a small private middle school. They do not have a 3D printer, but would like one. I would appreciate recommendations for a really...1 replies | 1235 view(s)
-
03-15-2024, 02:22 PMHello everyone, I am new to this forum and new to 3D printing. Recently bought a Bambulab X1 Carbon and have been playing around with it over the...3 replies | 1157 view(s)
-
03-15-2024, 10:19 AMHello again ! Another Stretch goal !! Huge lot of STL parts for many many sabers :) Let's go to the next one : the Old West saber :) Have...16 replies | 5530 view(s)
Newbie Question
Yesterday, 12:02 AM in Tips, Tricks and Tech Help