- Tab Content
- Bikeracer2020's Activity
- About Me
- Tab Content
-
Older Activity
-
Yesterday, 01:39 AMBikeracer2020 replied to a thread Is it worth getting more than the bare minimum for a 3d printer? in 3D Printers (Hardware)If you can buy something with a budget of up to 700, there are numerous better alternatives with more desireable features. Look for features such...1 replies | 246 view(s)
-
05-05-2024, 01:11 AMYou need to explain a bit more about what you mean by deregulated. Perhaps post a photo.2 replies | 841 view(s)
-
04-29-2024, 01:35 AMThe Qidi X-CF pro is enclosed and I never open the door until everything has cooled down to ambient temperature. Magnetic grip seems the same hot...4 replies | 1689 view(s)
-
04-28-2024, 02:12 PMBikeracer2020 replied to a thread New Ender 3 Neo: stops extruding filament halfway through in Tips, Tricks and Tech HelpCould be...... Extruder gears clogged with filament from grinding the filament. Extruder tension needs increasing but not if it's grinding...2 replies | 964 view(s)
-
04-28-2024, 02:02 PMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpGlad you got it sorted.7 replies | 2831 view(s)
-
04-28-2024, 04:18 AMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpThis is a guess...... Sounds like the G-code extrude command 'e' is missing in the start G-code. When you reinstalled Cura did you copy the...7 replies | 2831 view(s)
-
04-28-2024, 01:57 AMI think I'll have to look at a way of securing the edges that doesn't encroach too much on to the build area. My usual bed temp is 95 degrees, so...4 replies | 1689 view(s)
-
04-27-2024, 10:48 AMStarted biggish print 250 x 215, Qidi X-CF pro using ASA filament with nozzle temp 255 and bed temp 95, preheated chamber for over 30 minutes. ...4 replies | 1689 view(s)
-
04-24-2024, 01:59 AMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpPossibilities...... Filament route to extruder not free enough. Filament trapped under other windings on reel. Teeth on extruder gunged up with...7 replies | 2831 view(s)
-
04-22-2024, 03:57 PMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpCheck nozzle temp in the slicer in case you have accidentaly changed to a lower setting. Happened to me recently.7 replies | 2831 view(s)
-
04-22-2024, 03:49 PMBikeracer2020 replied to a thread Ender 3 S1 Mostly Metal Sprite Extruder Issue in 3D Printer Parts, Filament & MaterialsYou need a short piece of teflon or PTFE tube from the extruder into the hot end to support the filament.2 replies | 2682 view(s)
-
04-16-2024, 12:32 PMBikeracer2020 replied to a thread Catastrophic failure on Creality Ender-3 V3 KE in Tips, Tricks and Tech HelpThe filament monster is probably because the nozzle has a less than perfect seal to the hot end, causing the molten filament to leak. I don't know...1 replies | 2786 view(s)
-
04-14-2024, 01:46 AMDid You adjust the 'Z' offset in the slicer or just the 'Z' height when setting the initial nozzle difference? I should have made that clearer in...5 replies | 4777 view(s)
-
04-12-2024, 11:03 AMThe line is called a 'Z' seam, it happens where one layer ends and the next one starts. There are settings in the slicer as to where you want it...2 replies | 2609 view(s)
-
04-12-2024, 02:21 AMTwo suggestions...... Try Prusaslicer or Orca slicer. Or email.. may@qd3dprinter.com2 replies | 3832 view(s)
-
04-12-2024, 02:13 AMBikeracer2020 replied to a thread AI generated 3d models - Revolutionary or Evolutionary??? in 3D Modeling, Design, ScannersI think all this AI generated stuff is rapidly leading to a place where it will be impossible to distinguish between fact and fiction. In your...4 replies | 5324 view(s)
-
04-11-2024, 06:08 AMBikeracer2020 replied to a thread WHY DOES MY PRINT LOOK LIKE THIS Please help! in General 3D Printing DiscussionTry just using your standard slicer profile for the filament.1 replies | 2550 view(s)
About Bikeracer2020
Basic Information
Statistics
Total Posts
- Total Posts
- 621
- Posts Per Day
- 0.42
General Information
- Join Date
- 05-07-2020
Ender 3 Neo - Jam Problem
05-08-2024, 03:06 PM in Tips, Tricks and Tech Help