Subscribe to Our Newsletter Advertise
Close



Dig deeper, search our News website




Search:

Tag: motor

Search: Search took 0.00 seconds.

  1. The noise issue of stepper motors used in 3D printer

    Started by Victus, 02-13-2020 02:34 PM
    drivers, motor, printer, tmc 3 Attachment(s)
    • Replies: 5
    • Views: 5,829
    Last Post: 07-09-2020 06:59 AM
    by AngelArs  Go to last post

    Forum:
    General 3D Printing Discussion

  2. Design for a female hypoid gear (to fit over gear)

    Started by Moomaneast, 08-11-2017 05:20 PM
    design, gear, hypoid, motor, shaft
    • Replies: 0
    • Views: 2,784
    Last Post: 08-11-2017 05:20 PM
    by Moomaneast  Go to last post

    Forum:
    3D Modeling, Design, Scanners

  3. FFCP: About to install new z axis rod & motor. Installation steps or tips?

    Started by Grindeddown, 02-26-2016 03:45 AM
    flashforge creator pro, installation, motor, rod, z axis
    • Replies: 5
    • Views: 11,893
    Last Post: 09-15-2016 09:48 AM
    by mthompson239  Go to last post

    Forum:
    FlashForge Forum

  4. z18 primary drive motor bad ?

    Started by frankenkj03, 01-18-2016 09:21 AM
    drive, filament extruder, motor, z18
    • Replies: 2
    • Views: 7,015
    Last Post: 02-08-2016 09:32 PM
    by JasonPaulBennnett  Go to last post

    Forum:
    MakerBot Forum

  5. Delta goes wild when trying to Print?

    Started by wanseer, 12-31-2015 02:57 PM
    delta, motor, motors, movement, problem
    • Replies: 0
    • Views: 3,815
    Last Post: 12-31-2015 02:57 PM
    by wanseer  Go to last post

    Forum:
    Tips, Tricks and Tech Help

  6. Extruder not feeding

    Started by pgriffy, 08-11-2015 03:12 PM
    controller, electronics, extruder, hictop, motor 1 Attachment(s)
    • Replies: 3
    • Views: 9,171
    Last Post: 08-16-2015 07:41 AM
    by printbus  Go to last post

    Forum:
    Tips, Tricks and Tech Help

  7. Extruder Motor Replacement?

    Started by Vivid8, 06-03-2015 03:08 PM
    extruder, extruder issue, extruder motor, motor
    • Replies: 7
    • Views: 8,588
    Last Post: 08-09-2015 11:20 AM
    by lithgowlights  Go to last post

    Forum:
    FlashForge Forum

  8. Extruder stepper "clicking"

    Started by tigerprinter, 07-10-2015 04:49 PM
    extruder, filament, flashforge creator pro, motor
    • Replies: 7
    • Views: 13,109
    Last Post: 07-19-2015 11:10 PM
    by jfkansas  Go to last post

    Forum:
    FlashForge Forum

  9. Motor trouble

    Started by tigerprinter, 12-17-2014 01:51 PM
    2 Pages •
    1 2
    motor, problem, trouble 1 Attachment(s)
    • Replies: 16
    • Views: 14,050
    Last Post: 07-12-2015 11:34 AM
    by Raimond  Go to last post

    Forum:
    FlashForge Forum

Results 1 to 9 of 9