Close



Dig deeper, search our News website




Search:

Tag: gcode

Search: Search took 0.00 seconds; generated 44 minute(s) ago.

    • Replies: 1
    • Views: 7,177
    Last Post: 07-02-2024 01:00 PM
    by Bikeracer2020  Go to last post
  1. Control two extruders?

    Started by pescador, 06-17-2022 05:08 AM
    control, extruder, gcode, motherboard, prusa
    • Replies: 2
    • Views: 3,918
    Last Post: 06-21-2022 05:00 AM
    by pescador  Go to last post
  2. CURA adds 0.04mm layer height to Gcode ??!

    Started by FME, 08-12-2019 04:27 AM
    bug, cura, gcode
    • Replies: 2
    • Views: 5,010
    Last Post: 08-13-2019 10:26 AM
    by curious aardvark  Go to last post
    • Replies: 0
    • Views: 6,220
    Last Post: 07-25-2019 05:27 AM
    by ruanlotter  Go to last post
  3. Qidi Tech 1 Simplify 3D Startup Script

    Started by KludgeGuru, 04-17-2016 08:51 AM
    2 Pages
    1 2
    gcode, qidi, script, simplify3d
    • Replies: 13
    • Views: 44,328
    Last Post: 01-09-2019 06:50 AM
    by curious aardvark  Go to last post
  4. Bed leveling scripts/G code

    Started by synint, 09-23-2017 01:50 AM
    gcode, i3 pro x, script
    • Replies: 0
    • Views: 6,877
    Last Post: 09-23-2017 01:50 AM
    by synint  Go to last post
  5. Has Anyone Experienced This Strange Movement?!

    Started by alielsayid, 06-27-2017 08:50 AM
    extruder, firmware, gcode, marlin
    • Replies: 1
    • Views: 6,261
    Last Post: 07-05-2017 01:31 PM
    by Roberts_Clif  Go to last post
    • Replies: 0
    • Views: 3,299
    Last Post: 02-15-2017 12:26 PM
    by xelaciraptor  Go to last post
  6. 3D printer wont create smooth layered edges

    Started by VeiledOne, 02-17-2016 08:01 PM
    • Replies: 7
    • Views: 10,594
    Last Post: 02-20-2016 09:45 AM
    by 3dex ltd  Go to last post
  7. ReplicatorG -0400 - A question about GCode

    Started by Ward, 11-26-2015 08:22 AM
    2 Pages
    1 2
    gcode
    • Replies: 19
    • Views: 10,869
    Last Post: 11-27-2015 03:12 PM
    by Ward  Go to last post
    • Replies: 0
    • Views: 3,135
    Last Post: 10-30-2015 03:19 PM
    by Hoth  Go to last post
  8. Immediate gcode commands

    Started by Joymaker, 09-29-2015 05:16 PM
    command, gcode, immediate mode, interactive
    • Replies: 3
    • Views: 4,739
    Last Post: 10-07-2015 06:34 AM
    by curious aardvark  Go to last post
Results 1 to 12 of 12