Results 3,291 to 3,300 of 4110
Thread: Qidi Tech 1 - Replicator 1 clone
-
09-22-2016, 02:56 PM #3291Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-22-2016, 04:29 PM #3292
- Join Date
- Sep 2016
- Posts
- 80
-
09-22-2016, 05:40 PM #3293
Thanks! Yes, the cable chain is a needed upgrade for long term printing. I still have to print the blowers but will aim for this weekend. The accordion support is great when it all comes out in one shot.
Thanks!
Nice, picked myself up a pair too.Last edited by cncartist; 09-22-2016 at 05:55 PM.
-
09-22-2016, 06:59 PM #3294
Here is a link to where I got help and settings for OctoPi.
http://www.thingiverse.com/groups/qi...h-i/topic:7918
Every now and then I have to click "Restart OctoPi" but for the most part it works well.
Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-22-2016, 07:02 PM #3295
The accordion support was great. I just took my needle nose pliers, pushed from the open end towards the inside of the blower so that it broke free of the supports at the starting area. Then I took the just the end and started pulling it out. It all came out. Nice and clean.
I printed the blower nice and slow as well to get the best layers I could in ABS.
Right now I am printing the calibration cube with the blower. Fingers crossed.
Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-22-2016, 07:47 PM #3296
Well the box was much much better with the dual blower. I am trying Benchy again to see how it goes. I hope this time it goes better.
Extruder is at 200c bed at 40c, no sides or top, and ambient temp in the room is 67f.
Fingers crossed. I think I have some things I want to print in PLA/PHA so I am hoping this time it gets that last little bit set.
[IMG] [/IMG]Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-22-2016, 09:03 PM #3297
The cube looks pretty good to me!
Took a picture of the printer running at night with my LCD Night Shade (black) covering the front panel LCD. The lights are also off via the on/off switch I wired into the lighting system.
-
09-22-2016, 09:34 PM #3298
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
-
09-22-2016, 09:47 PM #3299
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
Syd
You've probably seen this already. DaDave is rocking on!
http://www.thingiverse.com/thing:1779274
-
09-22-2016, 10:49 PM #3300
Qidi X Plus 3 Paper thin first...
Yesterday, 01:15 AM in General 3D Printing Discussion