Results 31 to 40 of 96
Thread: Anyone used Printbite surface ?
-
09-07-2016, 10:24 PM #31
One thing I'm wondering is how I'm going to remove the QIDI blue tape thing to install the Printbite.
Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-08-2016, 05:00 AM #32
about 10C - I set mine at 70c and get 60c at the bed surface though bear in mind I have a 3mm aluminium plate as well as the printbite attached to me original bed.
I haven't had any issues with anything sticking when running it at 60c (surface temp)
Don't bother removing the tape, just stick the printbite on top :-)
-
09-09-2016, 02:00 PM #33
PrintBite order got refunded. It turned out they were out of the size for the QIDI printer as well. Bummer.
Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-09-2016, 04:51 PM #34
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
Here is one way of removing it:
https://youtu.be/KaFMr4gx_tc
-
09-09-2016, 04:52 PM #35
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
https://youtu.be/EkIwv_uEv3A
Sorry, picked up the wrong link
-
09-09-2016, 07:12 PM #36Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-10-2016, 12:39 PM #37
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
-
09-10-2016, 02:31 PM #38
Just get a bigger bit and 'cut' it to size.
The logical one is the 30x30 - which gives you two beds for a few quid more than the cost of one.
-
09-10-2016, 03:05 PM #39
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
-
09-10-2016, 03:14 PM #40
Nice!!
I have made the center plug under the bed, the door clip and I am making the other interior caps today.
I have not gotten to the parts bin, I just finished a mount system for my RPi3 and Pi Cam and mounted them up a few mins ago. I had my OctoPi system hanging all over the place now it is nice and neat, just have to make ribbon cable clips and all will be good. I will upload pics later.
Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
Ender 3v2 poor printing quality
10-28-2024, 09:08 AM in Tips, Tricks and Tech Help