Results 11 to 20 of 21
Thread: 3D Systems CubePro
-
10-28-2015, 08:23 AM #11
- Join Date
- Oct 2015
- Posts
- 2
We have had a CubePro since March. It is capable of very good prints. But we had great difficulty with the filament. It breaks frequently. I counted 17 breaks in one cartridge over time. It was broken in 3 places at once as we attempted one print job.
When it breaks like this it is very difficult to get out of the tube. The last cartridge I attempted to use was tangled up and would not come out of the cartridge. This was a new cartridge still in a sealed foil container. The other problem is clogged print jets.
I am dealing with one now. We may have to replace the print jet assembly again. It is very difficult to thread the filament into the print jet to begin with.
-
10-28-2015, 09:04 AM #12
We have a couple of cubes in our print farm (both 3 & Pro) and I have noticed the same thing. It prints well but I have had several cartridges break filament. It seems to be more prevalent in the PLA Cartridges and is a real pain to take them apart and re-thread them. I also have a brand new cartridge of Black that just refuses to print!
-
05-20-2016, 02:14 AM #13
- Join Date
- May 2016
- Posts
- 2
Was hoping this was a more hands off machine, and was attracted by the boasted high print speed. Definitely has needed a lot of attention. Still haven't figured out why the software can't always properly render supports for overhanging designs. Print speed is fast!
-
05-20-2016, 05:03 AM #14
Are you using the Support-borders setting? The other alternative is to make use of the dual heads (if you have a dual head version and use their Infinity wash away support filament, basically PVA.
-
06-06-2016, 10:38 AM #15
- Join Date
- Apr 2015
- Location
- Northern Ohio
- Posts
- 198
We have one at work and while well built it is essentially worthless. The filament breakage and the print quality (while it has gotten better) is still sub standard. The flash forge that I have at home just blows it away. The biggest PITA is the software and support structures. It is almost impossible to remove the supports on an intricate part. To anyone even concidering any 3D Systems product on the lower end to run. There are way better choices out there.
-
06-06-2016, 10:43 AM #16
I had heard that 3D Systems is discontinuing all their low end printers including the Cube and Cube Pro?
-
06-06-2016, 11:27 AM #17
- Join Date
- Apr 2015
- Location
- Northern Ohio
- Posts
- 198
I have not heard that but it wouldn't surprise me a bit. They tried to shove their proprietary everything into an open systems market. If they had a product worthy of it with the software to back it up I might be able to live with it.
-
06-06-2016, 03:31 PM #18
- Join Date
- Jan 2014
- Location
- Oakland, CA
- Posts
- 935
I heard they discontinued the entry-level Cube printer at the beginning of the year, but as far as I know they're still producing and selling the Cube Pro - you can Buy One Now, in fact: http://www.3dsystems.com/3d-printers/personal/cubepro
-
06-06-2016, 05:26 PM #19
-
06-14-2016, 12:27 PM #20
- Join Date
- Apr 2015
- Location
- Northern Ohio
- Posts
- 198
That is essentially a flash forge creator pro knockoff. I have a FF printer now and I like it a lot. It out performs the cube hands down. I am not looking for a hands off printer quite the opposite. I want a printer where I have control over everything like I do with symplify3d and my FF
Printing time- Is this right?
09-13-2024, 07:51 AM in General 3D Printing Discussion