Close



Page 3 of 3 FirstFirst 123
Results 21 to 25 of 25
  1. #21

    Post install results

    All,
    I installed this monitor on my FF Creator Pro and have run it for several days now. Initial thoughts: Works Great!

    I had 2 prints pause because of knotted filament. I was able to back up to the utilities menu, unload, straighten the knot, reload, and 'unpause' the printer. There was no noticeable flaw in the print job. I was using Makerware 2.4 at the 'Standard' settings and a 10 second delay on the monitor

    For this printer, I would extend the mounting rails so the filament entrance is aligned with the center of the spools which would decrease the potential problems. I had to remove the filament tube holder, https://www.thingiverse.com/thing:409297 that I had installed.

    Major note: the slower the print speed the longer the delay needs to be otherwise the monitor pauses the printer frequently. I was testing Ninjaflex filament at 30 mm/sec print speed and had to increase the delay to almost 30 seconds.

    Enjoy!

  2. #22
    Engineer-in-Training ServiceXp's Avatar
    Join Date
    Apr 2015
    Location
    USA
    Posts
    379
    Follow ServiceXp On Twitter Add ServiceXp on Google+ Add ServiceXp on Thingiverse
    Quote Originally Posted by toybuilder View Post
    #1 depends on the printer to signal a start of a new job to the monitor. The monitor itself could support this feature. In fact, one could wire already wire a signal line to the RST pin on the expansion connector to do this.
    #2 Width measurement would add complexity and cost; and would require software on the host software or firmware on the printer to do something useful with the information. I believe people at SD3D is trying to do something along those lines. On Sailfish-based firmware (FF's for example), there's no good way for dynamically compensating for filament diameter, as the x3g format specifies target positions in stepper counts.
    #3 Would require additional hardware to connect to the network, which this device cannot do on its own. Your sensors.org idea could work, though.

    The reason for the manual reset of the sensor is simply because there's no other way to tell the difference between an end of a print job and a failed print. So the Tunell monitor is designed to take a "start of job" signal in the form of the reset button. As I mentioned, with additional development (firmware on the Tunell monitor and the firmware or software of the device connected to the monitor), it would be possible to automate this process.

    Thinking outside the box, brings features that add value to a product. Currently the cost verses the value of the product is to great for me, but again that's just me.

    Outside the box thinking: (a few example)

    1) Monitor machine wattage : If watts > X and filament stops, go into fault. No need for user intervention.
    2) Add small display to simply display average filament width over distance. Yes it would require more technical expertise but it's a HUGE value to the product. If it was easy, then everyone would be doing it..
    3) Maybe out of the scope of the device, but you must admit, it's main purpose is notification, and hence far more value over a simple tone.

    I don't mind spending money on things, but there has to be value to the device, IMO currently this device does not have any more value then the $25 alternatives out there. Cheaper if you build one yourself.

    I hope you keep working on it and improve and expand it's functionality, because I think the idea is sound.

  3. #23
    Technician 34Ford's Avatar
    Join Date
    Jun 2014
    Location
    North Carolina
    Posts
    53
    I need something like this so I can tell when this cheap a$$ SainSmart filament breaks.

  4. #24
    Quote Originally Posted by ServiceXp View Post
    1) Monitor machine wattage : If watts > X and filament stops, go into fault. No need for user intervention.
    2) Add small display to simply display average filament width over distance. Yes it would require more technical expertise but it's a HUGE value to the product. If it was easy, then everyone would be doing it..
    3) Maybe out of the scope of the device, but you must admit, it's main purpose is notification, and hence far more value over a simple tone.
    #1 and #2 adds more complexity to the device. If you can do it for $25, great!

    #3 - I think the Tunell monitor's approach of pausing the printer is the right way to go. Sending a notification without pausing the printer won't help if you're not there to fix the problem right away. Similarly, those simple filament detectors that just turns on an alarm have the same problem - you have to be there to hear it.

  5. #25
    Engineer-in-Training ServiceXp's Avatar
    Join Date
    Apr 2015
    Location
    USA
    Posts
    379
    Follow ServiceXp On Twitter Add ServiceXp on Google+ Add ServiceXp on Thingiverse
    Just about anyone can do this for much less then 25 bucks. With this and this we are talking less then 5.00 really, albeit only detecting outages, add a MySenors board (another 10 bucks) and you have a communicating system (for those who have that infrastructure already setup) that will push alerts to any number of people.

    If one wants to get really fancy, use a simple encoder, and CT circuit on the same MySensors 'board' and you have a monitor (not just detecting outages), and current sensing system for printer state detection (no need to hit a reset switch on every start) along with a communication system, all for around 40 bucks.

    I know it sounds like I'm hassling you over your project, and perhaps that is a bit true. I'm not saying your product is bad, I'm just saying for ME the ROI is way to low. For those that lack the motivation/time and have the money to spend; your product looks like its perfect for simple filament movement detection.

Page 3 of 3 FirstFirst 123

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •