Results 41 to 50 of 101
Thread: I need some serious help
-
10-23-2015, 03:01 PM #41
Nick,
They have you compiling a Marlin version with Arduino IDE version 1.6, which is a terrible idea. It's known to be plagued with issues. Good news is I've got a 0.92.5 (latest) Repetier-Firmware for you to upload and try.
Here's what you need:
Your firmware (I made this using Repetier Firmware Configurator):
https://drive.google.com/open?id=0B1...GVwVE9LT2ZTcXM
The latest version of Repetier-Host:
http://download.repetier.com/files/h...Host_1_5_6.exe
And Arduino IDE 1.0.5 (even though Repetier-Firmware can be compiled with IDE 1.6):
http://arduino.googlecode.com/files/...r2-windows.exe
Before you upload the firmware do this in the Arduino IDE:
File -> Examples -> EEPROM -> eeprom clear
Then upload that sketch. It's smart to clear out your eeprom before you upload any new firmware.
Please be careful when you do your first movements with the new Firmware. Hover over that power switch. I'd be really surprised if I got EVERY setting right the first time, but hey, maybe. Also...you can now use Repetier-Host to do everything. It has a manual control tab that you can send G-Code and movements through. Unlike Pronterface though, commands are qued until they complete. So if you send gcode to bring your hot end up to temp, then other commands wont go through until the hot end reaches the set temperature.Last edited by LuckyImperial; 10-24-2015 at 03:06 PM.
-
10-24-2015, 07:37 PM #42
- Join Date
- Oct 2015
- Location
- Great Falls Montana
- Posts
- 52
thank you , i got them downloaded and will start trying to test it maybe tomorrow night. Just kinda taking a break this weekend. plus im waiting on new hotend which should be here on tuesday. What kind of errors might i be watching for ?
-
10-24-2015, 08:35 PM #43
The obvious thing is motors moving in inverse directions. You might also have unresponsive endstops if I didn't get their settings right.
If you can successfully do a G28 then you're off to a really good start.
-
10-27-2015, 08:15 PM #44
- Join Date
- Oct 2015
- Location
- Great Falls Montana
- Posts
- 52
so i have new hot end (not installed yet) I got all software installed , repietier seems alot nicer btw. When i hit home (g28) It trys to dig to china. I can hit endstops and it seems to be firne on those.... whay to do to fix motor direction?
-
10-27-2015, 08:21 PM #45
- Join Date
- Oct 2015
- Location
- Great Falls Montana
- Posts
- 52
nvm I found that , g28 seems to work!!!!! ..............now what? Should i test everything else ? proper directions when moving head.... extruder heating.... fan coming on ? or is there something else?
Im getting kinda excited
-
10-27-2015, 09:31 PM #46
haha dig to china. That's good.
Did you get the latest version Repetier-Host installed? If so, you can connect using that and make EEPROM changes using Config -> Firmware EEPROM Configuration. This is where a lot of your calibration settings are.
The next steps would be dialing in your calibration settings. Z-Height, Diagonal Rod Length and Horizontal Radius. All of these I plugged in from the Marlin configuration.h file you linked in your dropbox, but that doesn't mean their perfect. Z-Height first, which should be easy. Make sure at Z0 X0 Y0 passes the paper height test. Increase or decrease Zheight in EEPROM to adjust. Always do a G28 after eeprom changes. Sorry, I'm in class right now, but it sounds like you're off to a great start.
After calibration you should start looking into the extruder motor. Bring you hot end up to temperature and try to extrude some filament. Hopefully it extrudes in the right direction haha.
-
10-29-2015, 10:36 PM #47
- Join Date
- Oct 2015
- Location
- Great Falls Montana
- Posts
- 52
okay so i am back to where i started , everything seems fine up to the horizontal rod radius .... changing the value , even to the extreme , changes nothing.
First g28 , then i raised my z height from 338.9 to 350
Then I used these cords.(g1 x0 y66 , g1 x057 y-33 , g1 x57 y-33 )
I took a measurement from print head to bed with paper height readings were as follows
z 1.10 x 1.00 y .30 , I moved my set screw on each to dial them all in to 1.00
now i measured middled at 11.30 no matter how I adjust the Horizontal rod radius , I can not get it to come any closer to 1.00
I feel like im doing something wrong.
-
10-29-2015, 11:14 PM #48
-
10-30-2015, 06:23 PM #49
- Join Date
- Oct 2015
- Location
- Great Falls Montana
- Posts
- 52
okay so I did your test. I made z0x0y0 perfect , then measured the others i get a pretty even 3/8 which is 9.52 mm thats just close thou, i dont have a means to really measureunder the head.
so yea lol
-
10-30-2015, 09:46 PM #50
- Join Date
- Oct 2015
- Location
- Great Falls Montana
- Posts
- 52
i think i might be able to get an accurate exact reading , do you need it exact
Holes and pockmarks in print walls
06-04-2024, 09:14 AM in General 3D Printing Discussion