Results 11 to 20 of 22
Thread: Sintratec SLS 3D Printer
-
03-29-2015, 10:36 PM #11
Project funded, shipping in July.
-
08-15-2015, 08:39 AM #12
Just got my Sintratec SLS printer kit yesterday
pictured below
It's gonna take me a few days to build it, the quality of the build is very good, i'm impressed, all neatly labeled with clear instructions, a joy to build !
I visited the Sintratec team also yesterday near Zurich, pretty cool guys, they showed me the latest parts they printed, after improving their software, amazing surface finish, better than i was expecting, you just don't see the 100 microns layers, and the corners are so sharp, unbelievable.
Will put some pictures of my first parts, you can see some on their Facebook page.
IMG_20150815_085921.jpg
-
10-21-2015, 06:52 AM #13
I am interested in buying the Sintratec Kit. Does anyone have experience with this printer? I would love to hear about your experiences and 3d printing ventures. Would you recommend this printer?
-
10-21-2015, 11:00 AM #14
- Join Date
- May 2015
- Posts
- 4
I would love to buy this printer for my 3D printing company. I can't afford it, that's why I set up this crowdfunding campaign. For more information read the campaign.
Thanks allot!
http://igg.me/at/HelpProtoprint/x/12491539
-
10-29-2015, 09:29 AM #15t got fully funded on Indiegogo just a few months ago! They will begin selling them in a few months,
-
02-24-2016, 12:58 AM #16
- Join Date
- Feb 2016
- Posts
- 1
I must ask. Im very interested in buying a Sintratec printer but Ive been told that it can only successfully sinter black materials, because of its low power laser. My question to Sintratec, why didnt you raise the wattage of the laser so that the printer was capable of more? Seems perfectly simple to me..
-
03-01-2016, 09:28 AM #17
Hey Hatmpatn
Its not quite that easy, as there is another factor than just the wattage of the laser diode. The main reason we just use black powder is the wavelength of our the laser diode. its different from the CO2 laser commonly used in SLS printer. The white powder reflects most of the energy from the diode because of that particular wavelength, making it almost impossible to sinter it. increasing just the power of the diode wont change this fact.
We are currently working on releasing more powders, but to provide optimal support for our product, we just focus on black nylon for now.
-
03-17-2016, 04:14 PM #18
- Join Date
- Jun 2014
- Posts
- 885
This thread is a bit on the quiet side. I'd hoped for more activity, especially from Sintratec owners. I'd received mine from the pre-order option after the campaign ended, and only this week have started to build it.
The instructions are indeed well written, but with a serious omission, in my opinion. As an example, assembling the door requires one to bolt together four extrusions using some well designed fittings. The first pages of the instructions show that clearly. What it doesn't show, and should show, is the need to slide in the internal nuts at that time. In two later locations in the same section (door build), it becomes necessary to disassemble the previous structure.
If the drawings had listed the increased part count and placed them appropriately, it would have reduced my build time substantially. Of course, now that I'm aware of this nuance, I will keep my eyes open for the future segments of construction.
Perusing the second segment manual, I see exactly the same thing. Assemble the base frame, then have to take it apart to slide in the nuts. I'll avoid that by making pencil marks in the manual after I print it out, to ensure I won't go through this again.
Are there other forums for this printer and its users?
-
03-17-2016, 05:41 PM #19
Hello fred_dot_u
Thanks for your feedback on our guide.
We did not omiss the point you stated. Its clearly shown in our best practice guide how to Insert nuts without disassembly of the segment. You can easily clickt them in from the side with a small allen wrench. Please check out the best practice guide provided with your sintratec KIT.
You can always contact us directly via customer portal with your concerns or problems.
Best regards
Roman
-
03-17-2016, 06:08 PM #20
- Join Date
- Jun 2014
- Posts
- 885
Well, that's a curious development. I did read the best practice guide. Unfortunately, I've just discovered that the version I have is one from last year! Moments ago, I download the current version and have found the notation you reference. That will most certainly make things easier for me for the remainder of the assembly.
thank you for clearing that up for me. I appreciate your quick and kindly support.
Holes and pockmarks in print walls
06-04-2024, 09:14 AM in General 3D Printing Discussion