Close



Page 9 of 10 FirstFirst ... 78910 LastLast
Results 81 to 90 of 93
  1. #81
    Technician
    Join Date
    Jun 2014
    Location
    3D Printer Tellus
    Posts
    83
    Quote Originally Posted by 3DPBuser View Post
    Is T-Glase not PET also?
    Yes as the one above said, there are different T-Glase with different PET material

  2. #82
    Technologist
    Join Date
    Jul 2014
    Location
    mexico
    Posts
    120
    Add bshadown on Thingiverse
    But taulmans make only nylon right? Sorry im lost on this one.

  3. #83
    Super Moderator RobH2's Avatar
    Join Date
    Nov 2013
    Location
    Baltimore, MD
    Posts
    899
    Add RobH2 on Thingiverse
    The Weld-on #4 glued the PET very nicely. It's water thin and it wicks. It's like gluing acrylic. It wicks in and sets very quickly. If you are careful and don't drip it everywhere, you can never see it.
    Bambu P1S/AMS
    NVision4D http://nvision4d.com

  4. #84
    Technician
    Join Date
    Jun 2014
    Location
    3D Printer Tellus
    Posts
    83
    Quote Originally Posted by bshadown View Post
    But taulmans make only nylon right? Sorry im lost on this one.
    Taulman is just a brad name, they have something called T-Glase which basically is PET material.
    Taulman also have something called NYLON, so total 2 lines.

    Basically you can buy other brands, as long it is PET material you will have the so called T-glase.

    Nylon is well Nylon.

  5. #85
    Where are you all ordering PET from?

  6. #86
    Engineer
    Join Date
    Oct 2013
    Location
    new jersey
    Posts
    752
    www.madesolid.com has their pet+, colorfabb has their xt line which is currently just in clear but they have some colors on the way in a couple few months. there is also taulman's t-glase. i have done more printing with the madesolid solid stuff than any of the other by a long shot.

  7. #87
    Super Moderator RobH2's Avatar
    Join Date
    Nov 2013
    Location
    Baltimore, MD
    Posts
    899
    Add RobH2 on Thingiverse
    I use PET+ from Madesolid.com based on Jim's recommendation. I just ordered some T-Glase to test it to see if it's any different. I'll report back if I find anything significant about it.
    Bambu P1S/AMS
    NVision4D http://nvision4d.com

  8. #88
    Engineer
    Join Date
    Oct 2013
    Location
    new jersey
    Posts
    752
    Rob keep an eye on the extrusion of the tglase. Taulmans stuff is always good but the extrusion dia can be all over the place esp in the tglase. Not sure if they have been able to correct that or not. Just take some measurements and let me know what you find. Im curious.

  9. #89
    Super Moderator RobH2's Avatar
    Join Date
    Nov 2013
    Location
    Baltimore, MD
    Posts
    899
    Add RobH2 on Thingiverse
    Jim, do you mean that it drifts throughout a single spool or that each spool has a different diameter? I'll keep an eye on it and report in. Thanks for the heads-up.
    Bambu P1S/AMS
    NVision4D http://nvision4d.com

  10. #90
    Engineer
    Join Date
    Oct 2013
    Location
    new jersey
    Posts
    752
    The dia might go from 1.6 to 2mm in the same spool. It will have wide spots and you end up with air prints. It was a big issue with the tglase back when it was released. Not sure about now. It was the reason i didnt try it and went with masesolid. The new colorfabb xt is excellent. I had a sample of the black and it prints super easy, bridges really well and its super strong like a piece of polycarbonate when its done. Just not avail yet.

Page 9 of 10 FirstFirst ... 78910 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •