Close



Page 2 of 2 FirstFirst 12
Results 11 to 18 of 18
  1. #11
    Staff Engineer Roberts_Clif's Avatar
    Join Date
    Jun 2017
    Location
    Washington State, USA
    Posts
    1,167
    Add Roberts_Clif on Thingiverse
    Natural PLA is made from corn and is generally considered safe to use with food.

  2. #12
    Super Moderator curious aardvark's Avatar
    Join Date
    Jul 2014
    Posts
    8,801
    yep.
    actually so is abs.
    Pretty much the first things I ever desinged and printed were sausage stuffer tubes in abs.
    6 years later, still using them.
    That was in the frustrating months before I discovered that people lied about pla being brittle and weak.

    Like everything that's in contact with food - wash it properly after use and it's fine.

  3. #13
    High Purity: PETG has low shrinkage rate, high transmittance, even print larger models perform well.

  4. #14
    Technician
    Join Date
    Dec 2018
    Posts
    62
    PLA is food safe but PLA is too soft for hot beverages. The plastic will slowly flow at the normal temperatures. On the other side, The FDA considers PETG to be safe for food contact. PETG is very durable and more flexible than PLA.

  5. #15
    Student
    Join Date
    Apr 2019
    Location
    scotland
    Posts
    11
    Follow inov3D On Twitter Add inov3D on Facebook
    its allways good to refer to the manufacturer guidelines but there is a lot of things to take into mind

    Where is the printer
    is the printer in a dusty place is there particles flying around all of this can go into your printed part

    Print bed
    what is the print bed made out of

    Oil
    oil that is on your printer to help lubricate some parts could end up going on to the printed part

    there is a lot more to take into consideration
    https://www.inov3d.net/petg-3d-printer-filament

  6. #16
    Super Moderator curious aardvark's Avatar
    Join Date
    Jul 2014
    Posts
    8,801
    PETG is very durable and more flexible than PLA.
    that depends almost entirely on print temperature.
    Print it at 220 - 235 and it's rigid and brittle.

    240 and above and it starts to toughen up.

    You still have to print it really slowly - which just annoys me :-)

  7. #17
    PETG likes 245 and you have to have your starting height and extrusion multiplier correct other wise you end up with brittle parts or over stringy parts. After my normal 2 walled square to check starting height and extrusion multiplier I print a 30x30mm 2 layer high solid square. There should be no space between the thread of plastic with good bonding between them. and when the extrusion output is correct, it will bend back and forth without snapping. I had a part that broke easier than I would have expected and thought it was a temperature issue.. but it was under extruded even though the 2 walled square measured correctly. Since that time I always print at least 1 layer of the 30x30 to make sure the threads are bonded to each other. For instance the other day, an extrusion multiplier of .90 made a correctly sized wall but the 2 layer square snap along extrusion lines.. at an extrusion multiplier of .92 the square could not be broken..

  8. #18
    Student
    Join Date
    May 2019
    Location
    Dongguan,China
    Posts
    1
    Follow Icey On Twitter Add Icey on Facebook Add Icey on Google+
    3D printing is a kind of rapid prototype technology, which based on the digital model file. It use the powder metal or adhesive materials like plastic to construct the object by the way of step by step printing.

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •