Hiya,

you're not the only confused one. geetech is the seller and the tech support i was getting... but when ever i asked for the build manual they sent me to the nextday page. most of the things on there wernt what i was given or i was given something that wasnt on the manual, i had to go loads of places to find out how to actually build my printer as the instructions were not clear. the geetech told me to download a driver that actually blue screened my laptop... so after that i got in contact with the geeetech people who were going round in circles for almost a year.... i got this printer last christmas.

i'l try my best to clear up what i actually have:

here is the manual they gave me... i was using that board until i realised that they had made it wrong and it wasn't even functional, so i now have a ramps 1.4 board

1.0 Electronics
1.1
Fully assembled Sanguinololu & Soldered with Hot end power & Thermistor attached.
1.2
Sanguinololu Power Cables
1.3
(NO LONGER IN USE)



3x Mechanical Endstops with Completed Wiring I Had to change these over with new one as i had plugged these into 12V i think?
©2012 NextDayReprap
Prusa Mendel Kit Build Manual V1.01 - 07/2012
1.0 Bill of Materials - Reprap Prusa Mendel Build Manual
1.4
550W ATX PSU
1.5
ATX Power Supply Adaptor
1.6
V2 Heat bed with Surface Mount LEDs/Resistor & Soldered Power Cable (inc Thermistor)
1.7
5 x Nema 17 Stepper Motors with Connectors & Crimps
©2012 NextDayReprap
Prusa Mendel Kit Build Manual V1.01 - 07/2012
1. 0 Bill of Materials - Reprap Prusa Mendel Build Manual
1.8
Fully assembled Hot End wired for Power & Thermistor with Mini Fit Molex connectors.
1.9
Mains Power Lead (Kettle Type) & 1M USB 2.0 Cable
2.0 Rod


6x 370mm A2 Stainless 1.25mm Pitch Threaded Rod - YUP
3x 440mm BZP 1.25mm Pitch Threaded Rod
4x 294mm BZP 1.25mm Pitch Threaded
2x 210mm BZP 1.25mm Pitch Threaded Rod
2x 50mm BZP 1.25mm Pitch Threaded Rod
2x 420mm Steel Round Rod
2x 350mm Steel Round Rod
1x 19.5mm Steel Round Rod ( Extruder Idler)
2x 390mm Threaded Rod
©2012 NextDayReprap


Prusa Mendel Kit Build Manual V1.01 - 07/2012
1.0 Bill of Materials - Reprap Prusa Mendel Build Manual
3.0 Nuts & Bolts


6 x M2 16mm Hex Socket Bolts
30x M3 10mm Hex Socket Bolts
15x M3 20mm Hex Socket Bolts
2x M3 40mm Hex Socket Bolts
2x M4 50mm Hex Socket Bolts
2x M4 45mm Hex Head Bolts
4x M4 40mm Countersunk Hex Socket Bolts
6x M8 30mm Fender/Penny Washers
6x M2 Nuts
28x M3 Nuts
8x M4 Nuts
86x M8 Nuts
2x M3 Nylock Nuts
1x M8 Nylock Nuts
12x M2 Washers
56x M3 Washers
16x M4 Washers
88x M8 Washers
1x Hobbed Bolt
1x M3 10mm Grub Screw (Extruder Small Gear)
©2012 NextDayReprap
Prusa Mendel Kit Build Manual V1.01 - 07/2012
1.0 Bill of Materials - Reprap Prusa Mendel Build Manual
4.0 Bearings & Pulleys & Couplings
4.1
12x LM8UU Bearings (1 Spare) (Some may have been pre fitted to the printed parts) (which they were)
4.2
9 x 608ZZ Bearings (1 Spare)
4.3
2x 12 tooth T5 XL Aluminum Pulleys
4.4
2x Rigid Z Axis Couplings
©2012 NextDayReprap (see they keep mentioning this)
Prusa Mendel Kit Build Manual V1.01 - 07/2012
1.0 Bill of Materials - Reprap Prusa Mendel Build Manual
5.0 Springs
5.1
4 x Heat Bed Springs
5.2
2x Z Axis Springs
5.3
2x Extruder Springs
6.0 Timing Belts
6.1
2x 1M Brecoflex 6mm T5 Belt
©2012 NextDayReprap
Prusa Mendel Kit Build Manual V1.01 - 07/2012
1.0 Bill of Materials - Reprap Prusa Mendel Build Manual
7.0 Build Plate
7.1
Laser Cut Aluminum Build Bed
7.2
7.3
4x 51mm Bull Dog Clips (didn't include these, had to buy them my self)
225cm x 225cm Build Plate Mirror
©2012 NextDayReprap (and again)
Prusa Mendel Kit Build Manual V1.01 - 07/2012
1.0 Bill of Materials - Reprap Prusa Mendel Build Manual
8.0 Printed Parts
8.1
4x Bar Clamps
8.2
2 x Rod Clamps
8.3
4 x Belt Clamps
8.4
3 x Endstop Holder
8.5
4 x LM8UU Bearing Pillows
©2012 NextDayReprap
Prusa Mendel Kit Build Manual V1.01 - 07/2012
1.0 Bill of Materials - Reprap Prusa Mendel Build Manual


1 x Extruder
1 x Extruder Idler
1x Extruder Large Gear
1x Extruder Small Gear
1x X Carriage
8.7
2 x Frame Vertex
8.8
4x Frame Vertex with Foot
©2012 NextDayReprap
Prusa Mendel Kit Build Manual V1.01 - 07/2012
1.0 Bill of Materials - Reprap Prusa Mendel Build Manual
8.9
8x Bar Clamp
8.10
1 x X Motor Mount
8.11
1 x X Idler
8.12
1x Y Motor Mount
©2012 NextDayReprap
Prusa Mendel Kit Build Manual V1.01 - 07/2012
1.0 Bill of Materials - Reprap Prusa Mendel Build Manual
8.13
2x Z Motor Mount
8.14
2 x y-tensioner
8.15
2x Belt clamp nut holder


hopefully that has cleared some stuff up? you can down load the pdf i got from : http://www.geeetech.com/Documents/Re...0Optimized.rar