Results 21 to 30 of 33
Thread: Black ABS
Hybrid View
-
08-08-2014, 06:14 AM #1
so basically print the black at lower temp then, say 225 or 220 maybe ?
Got a new roll of black from a new supplier (to me) off ebay yesterday - haven't tried it yet . But the transparent filament I bought is great (again, different supplier).
Prices are really coming down - the three rolls I bought were all under £14 each including postage (can't remmber excatly but somewhere around £13.60 ish)
The transparent is really good stuff, nice sharp, clean prints.
I'll try the silver and black later.
For the record the filament that came with the printer was a roll of blue - that was printing great, but something in it blocked the print nozzle - and I haven't touched it since.
The FF white, on the other hand is really excellent. Again, very clean sharp prints even at .3 & .4 I went through about 3/4 of the roll in 2 days with zero issues and zero stringing even on large multipart prints.Last edited by curious aardvark; 08-08-2014 at 06:19 AM.
-
08-08-2014, 08:30 PM #2
While I may have had issues with their black, I will never forget the roll of White ABS that came with my printer... I haven't been able to buy as good as a white since, off anyone, INLCUDING Flashforge. The next white batch they sent me was an off white, and the batch after that was white, but more glossy white off colour. Their original white that came with the machine, printed Dry and perfectly.
The White I got with my machine was this amazing snow white, it was really really bright white.. the best white ABS I have still ever seen printed. I have bought dozens of whites now, and still can't find one as white!!
Every white I buy now is a little off, or bone colour.. man I just want pure white, like cocaine white!
-
08-19-2014, 08:01 PM #3
-
08-19-2014, 08:31 PM #4
I order one or 2 white rolls every fortnight, and I change suppliers every single time just in the hope I will find it again. It is the closest thing to a 'white plaster' print I have found, for someone like me that loves to paint, it's sorta like my favourite abs to print and paint.
-
08-22-2014, 12:54 PM #5
just a quickie - filament change advice works perfectly !
Thanks mate :-)
-
08-11-2014, 05:46 AM #6
well that definitely sounds like the white I got with the printer. Maybe they keep the old stuff to ship with new printers :-)
Have't bought any white from anyone else yet.
Hell, still haven't tried the silver (actually grey - not at all what I was expecting) or black yet.
IT;'s such a pain to change filament I tend to just run the roll down.
It reverses the filament for a few cms and then just stops - the motor is still making running noises, but I have to pull the filament out with pliers.
I've had the extruder apart and I can't see why it needs so much force to remove it. Even with the springy tension lever open the filament does not just pull out without massive force.
That said - it feeds it in no problem and works great once loaded - it's just I'm concerned about how hard I Have to pullt it to remove it - don't want to break anything.
-
08-11-2014, 08:57 AM #7
I change filament on the hour.
The Number 1 Rule...
When changing filament, LOAD for a few seconds and then UNLOAD.
It is trying to retract the filament that is causing you headaches. Inside that tube is is not 1.75mm, it's a bit bigger generally and it expands to fill the hole, not enough to lose pressure but wider than the original diameter. Feeding flushes this, and then you can unfeed and it comes right out - never ever jam again. As long as you push the spring you are OK.
-
08-22-2014, 01:53 PM #8
@robh - here you go - not sure where you were looking it was a couple posts above my last one :-)
No blockage just routine filament change. Push a few cms of old filament through, immediately back up and it comes out easy as you like :-)
I can move my pliers back tot he other end of the workshop where they belong.
-
08-22-2014, 02:08 PM #9Bambu P1S/AMS
NVision4D http://nvision4d.com
-
08-19-2014, 06:19 AM #10
that's what i do (i think). but i pretty much always end up having to snap the filament with pliers.
what you say makes sense though. I'll try it again later, cheers
Maybe I'm not feeding enough through before reversing it.
Please explain to me how to...
Today, 02:43 PM in 3D Printer Parts, Filament & Materials