Results 31 to 40 of 96
Thread: Anyone used Printbite surface ?
Hybrid View
-
09-07-2016, 10:24 PM #1
One thing I'm wondering is how I'm going to remove the QIDI blue tape thing to install the Printbite.
Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-09-2016, 04:51 PM #2
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
Here is one way of removing it:
https://youtu.be/KaFMr4gx_tc
-
09-09-2016, 04:52 PM #3
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
https://youtu.be/EkIwv_uEv3A
Sorry, picked up the wrong link
-
09-09-2016, 07:12 PM #4Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-10-2016, 12:39 PM #5
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
-
09-08-2016, 05:00 AM #6
about 10C - I set mine at 70c and get 60c at the bed surface though bear in mind I have a 3mm aluminium plate as well as the printbite attached to me original bed.
I haven't had any issues with anything sticking when running it at 60c (surface temp)
Don't bother removing the tape, just stick the printbite on top :-)
-
09-09-2016, 02:00 PM #7
PrintBite order got refunded. It turned out they were out of the size for the QIDI printer as well. Bummer.
Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-10-2016, 03:05 PM #8
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
-
09-10-2016, 02:31 PM #9
Just get a bigger bit and 'cut' it to size.
The logical one is the 30x30 - which gives you two beds for a few quid more than the cost of one.
-
09-10-2016, 03:16 PM #10
I will check back in a few mins then. The rep from there said they were out of most of them and for some reason several showed up as in stock. I was thinking going larger like you suggest to get an extra. I will ping them first and ask.
I almost pulled the trigger on the Borosilicate glass last night but I dont want the size that is a bit too small or the size that is just over-sized so I am trying to source one that is the correct size for the QIDI printer.
Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
Please explain to me how to...
Yesterday, 03:08 PM in 3D Printer Parts, Filament & Materials