Results 1 to 10 of 96
Thread: Anyone used Printbite surface ?
Hybrid View
-
09-07-2016, 07:42 PM #1
- Join Date
- Jan 2016
- Posts
- 326
Do I have to raise the temperature of the heated platform and/or extruder when using Printbite?
-
09-07-2016, 10:23 PM #2Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-07-2016, 10:24 PM #3
One thing I'm wondering is how I'm going to remove the QIDI blue tape thing to install the Printbite.
Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-09-2016, 04:51 PM #4
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
Here is one way of removing it:
https://youtu.be/KaFMr4gx_tc
-
09-09-2016, 04:52 PM #5
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
https://youtu.be/EkIwv_uEv3A
Sorry, picked up the wrong link
-
09-09-2016, 07:12 PM #6Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-10-2016, 12:39 PM #7
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
-
09-10-2016, 03:14 PM #8
Nice!!
I have made the center plug under the bed, the door clip and I am making the other interior caps today.
I have not gotten to the parts bin, I just finished a mount system for my RPi3 and Pi Cam and mounted them up a few mins ago. I had my OctoPi system hanging all over the place now it is nice and neat, just have to make ribbon cable clips and all will be good. I will upload pics later.
Editor in Chief
Bitsonline
Tips Appreciated But Not Expected
BTC: 16wxHvKd3oU6SVjv6FrenqhkvRmc8t7sPy
DASH: XqyaWxH896j9YeV1M35Gzb5gmRPmPbNDGq
-
09-10-2016, 04:44 PM #9
- Join Date
- May 2016
- Location
- Annapolis, MD
- Posts
- 523
This one is not by cncartist, but is an exceptionally useful hinge for the QiDi's front door. http://www.thingiverse.com/thing:1697406 If you slide it to the right it locks the door up in the open position, rotate down by 30 degrees and you can lift to remove the entire door. Kind of made the door clip unnecessary though.
-
09-08-2016, 05:00 AM #10
about 10C - I set mine at 70c and get 60c at the bed surface though bear in mind I have a 3mm aluminium plate as well as the printbite attached to me original bed.
I haven't had any issues with anything sticking when running it at 60c (surface temp)
Don't bother removing the tape, just stick the printbite on top :-)
Ender 3 Neo - Jam Problem
05-08-2024, 03:06 PM in Tips, Tricks and Tech Help