Toshiba Flashair SD Card Mapped in Windows

[scobo]

I ordered a W-03 card but still couldn't get it to connect to my router at first.
I finally figured out the problem, my router was using wifi channel 12 but the flashair only uses channels 1-11 apparently ......
http://www.toshiba.co.jp/p-media/wwsite/flashair.htm
(see bottom of page)
So I switched the router to channel 11 and it's now working great !
Can now save directly to the card from S3D or access it from a mapped drive on the windows desktop.

@beerdart, I suspect this might be the issue you're having too.
Check which wifi channel your router is using and try changing it if it's above 11.

[DaveB]

That's a good catch Scobo. A well positioned factoid in their data sheet, like the very last note on the page...

[scobo]

That's a good catch Scobo. A well positioned factoid in their data sheet, like the very last note on the page...

Yeah I would think that'll catch a lot of folk out.
They should've made that clear in the basic setup guide.

[DaveB]

So I purchased a W04 version. I've not been able to configure it to work as the W03 version does. I am sending it back and just getting another W03. I got close, but the card's behavior was not reliable. I am sure it was some misconfiguration issue on my part, but I couldn't figure out what it was.

Update: Got another W03 version card and after my usual random walk through configuration, it works like a charm.

[supertaz]

I'm sorry I didn't see your message before - the W-04 took me about 5 tries to get working, but it's been rock-solid ever since. The biggest thing is that you need to initialize it using the Toshiba software, I think. As annoying as it was to try to get it configured, once I got it working, it has handled being turned off, removed and reinserted, and lots of activity over the network and front panel, all without a single hiccup.

I'll report back whether my second one (which arrived yesterday) is as solid in my second Tech 1, once I've got it set up and working.

[ServiceXp]

With the video full screen (via YouTube rather than this forum) I could read the screen text well enough to copy off and key in the missing CONFIG file parameters. Everything is working slick as you please now. I am using the FlashAir with S3D on a QIDI 3D printer and it makes for a very sweet setup. Thank you very much ServiceXP for making and posting your video, it likely saved me hours of frustration.

I did find that having the NOISE_CANCEL=2 line present in the CONFIG file seemed to kill off the FlashAir's wifi connection, but all seems to be perfectly functional without that particular line in there. It's working, so I'm not gonna fix it.

All during this install process I was throughly confused by an SSID issue. Specifically, whose SSID was being referred to by the two entries in the CONFIG file? I finally got it that both the SSID entries (and their password) in the final CONFIG file are the same, and are the one for my home router/access point. I kept thinking they were different, or the FlashAir card's...not so.

You are welcome, I absolutely love the setup, now it's so easy to send prints to my printers right out of S3D.

I ordered a W-03 card but still couldn't get it to connect to my router at first.
I finally figured out the problem, my router was using wifi channel 12 but the flashair only uses channels 1-11 apparently ......
http://www.toshiba.co.jp/p-media/wwsite/flashair.htm
(see bottom of page)
So I switched the router to channel 11 and it's now working great !
Can now save directly to the card from S3D or access it from a mapped drive on the windows desktop.

@beerdart, I suspect this might be the issue you're having too.
Check which wifi channel your router is using and try changing it if it's above 11.

VERY nice catch scobo. I thought I had read that entire pdf, like twice.. :-) I'll add this in the video description.