Qidi Tech 1 - Replicator 1 clone

[wirlybird]

So now I have two bad spools of ABS from Makergeeks and they are unresponsive.

[wirlybird]

Anyone using MG raptor filament? What are the temps?

[DaveB]

Anyone using MG raptor filament? What are the temps?

I've used the yellow MG PLA Raptor material at 230/60. Great stuff too. I've also got rolls of green and white but have not printed anything with them yet. Syd has used it on some of his projects also.

[Syd_Khaos]

Anyone using MG raptor filament? What are the temps?

230c(ish) for nozzle
75 then drop to 60 for HBP.
Wanna slow it down like ya normally would with PLA....2400-2600mm/min or so is good for most stuff.

[Syd_Khaos]

HELP!!!!

I am trying to print this:
http://www.thingiverse.com/thing:831200

I have got all the parts but 1 printed. The one part I can not get done is 'LH_Green_Cape_body3'.
When sliced in S3D it is missing s big section of the model, making unprintable. Prior to slicing it looks as it should on the plate.

Here how it looks preslice:


Here is it sliced:


I can see NO errors in the model. Have even loaded it into Blender and confirmed its 100% manifold and all normals are facing the right way.
Any ideas??

[wirlybird]

HELP!!!!

I am trying to print this:
http://www.thingiverse.com/thing:831200

I have got all the parts but 1 printed. The one part I can not get done is 'LH_Green_Cape_body3'.
When sliced in S3D it is missing s big section of the model, making unprintable. Prior to slicing it looks as it should on the plate.

Here how it looks preslice:


Here is it sliced:


I can see NO errors in the model. Have even loaded it into Blender and confirmed its 100% manifold and all normals are facing the right way.
Any ideas??

Way cool. Coming from New England I love lighthouses. I'll check your part later when I get home.

[DaveB]

HELP!!!!

I am trying to print this:
http://www.thingiverse.com/thing:831200

I have got all the parts but 1 printed. The one part I can not get done is 'LH_Green_Cape_body3'.
When sliced in S3D it is missing s big section of the model, making unprintable. Prior to slicing it looks as it should on the plate.

Here how it looks preslice:


Here is it sliced:


I can see NO errors in the model. Have even loaded it into Blender and confirmed its 100% manifold and all normals are facing the right way.
Any ideas??

That's pretty odd Syd. I don't see why it ignores the center anulus and turns it into a support structure only. i tried exporting it thru some other SW and back into S3D with the same results.

[wirlybird]

HELP!!!!

I am trying to print this:
http://www.thingiverse.com/thing:831200

I have got all the parts but 1 printed. The one part I can not get done is 'LH_Green_Cape_body3'.
When sliced in S3D it is missing s big section of the model, making unprintable. Prior to slicing it looks as it should on the plate.

Here how it looks preslice:


Here is it sliced:


I can see NO errors in the model. Have even loaded it into Blender and confirmed its 100% manifold and all normals are facing the right way.
Any ideas??

You need to run all of the parts through a fixer. This one in particular is a mess. It looks fine once I fixed it.

[Syd_Khaos]

You need to run all of the parts through a fixer. This one in particular is a mess. It looks fine once I fixed it.

All of the other parts printed just fine.
What you using for a fixer?

[wirlybird]

All of the other parts printed just fine.
What you using for a fixer?

https://makeprintable.com/