Close
Flash Forge Inventor Series



Dig deeper, search our News website




Search:

Type: Posts; User: curious aardvark

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds; generated 7 minute(s) ago.

  1. sounds about right.

    sounds about right.
  2. Replies
    5
    Views
    98

    nylon would probably be too floppy. As well as...

    nylon would probably be too floppy. As well as being a more advanced filament to print properly.
    pla or petg would be absolutely fine.

    loads of free cad programs - I use openscad, which has a...
  3. Replies
    4
    Views
    159

    lose the abs. An enclosed printer is NOT a...

    lose the abs.

    An enclosed printer is NOT a temperature controlled heated printer.
    So abs will always be an issue. Plus pla is better anyway :-) (as you state on one of those links).

    I'll...
  4. pretty much the one thing you want in a used...

    pretty much the one thing you want in a used printer, is a total lack of use :-)

    Even an old 3d printer will still make things, so people selling used printers tend to fall into two categories.
    ...
  5. Replies
    4
    Views
    159

    so are there any actual pictures of the machine ?...

    so are there any actual pictures of the machine ?
    Or in fact of anything :-)

    And while you're here, presumably you've done a bit of research into arduino type boards to run these things.
    ...
  6. Replies
    1
    Views
    169

    Only thing I can think of is to check your...

    Only thing I can think of is to check your vertical endstop.
    Might have slipped. might not be properly fitted.

    Also make sure that you have the dimensions in correctly under the GCODE tab in...
  7. Replies
    82
    Views
    50,500

    Sticky: print hotter 190 ? wow. Don't think I've ever...

    print hotter 190 ?
    wow. Don't think I've ever printed pla lower than 200 and 210 is my standard for 90% of prints.

    Corners are lifted because you've got shrinkage - it's slightly fatter due to...
  8. Replies
    9
    Views
    368

    you're using the word vertices incorrectly -...

    you're using the word vertices incorrectly - which has confused me somewhat.

    You have lots of vertices in your build. It's a corner, there are lots of corners.

    Bolting the uprights directly...
  9. you do get what you pay for. whole lot of newer...

    you do get what you pay for. whole lot of newer tech and better quality kit in the prusa.
    The cr10 is a decent kit, but nothing like the prusa mk3.

    Thing is most 3d printers are pretty good. ...
  10. Replies
    9
    Views
    368

    why ? much easier to use corners.

    why ?
    much easier to use corners.
  11. if you're getting an i3 - then the prusa i3 mk3...

    if you're getting an i3 - then the prusa i3 mk3 is definitely the best on the market.

    Just got a lot more cool features than the cr10 :-)
    Not cheap, but probably worth the money.

    can you run...
  12. Formlabs New Fireable Ceramic resin !

    https://formlabs.com/blog/introducing-ceramic-3d-printing-form-2/?utm_source=direct&utm_medium=email&utm_campaign=ceramic18&mkt_tok=eyJpIjoiTVdNeVl6VmpNalV5TkdGaiIsInQiOiJIcEpWXC9DWlRaNlVFcHJEVFZSZnZR...
  13. Replies
    4
    Views
    259

    the problem with aliexpress is that it's just a...

    the problem with aliexpress is that it's just a middleman between a lot of different chinese factories.
    Think that's where my silicon heatpad for the big delta came from.
    Had np problem with that...
  14. Replies
    2
    Views
    170

    what temperature and retraction settings did you...

    what temperature and retraction settings did you use ?
  15. http://slic3r.org/download slic3r claims to...

    http://slic3r.org/download
    slic3r claims to support dlp - linux versions.
    https://octoprint.org/

    probably worth a look.
  16. older slicer/creation workshop shouust as well. ...

    older slicer/creation workshop shouust as well.
    Presumably the cws file consists of a series layer masks, rather than the instruction set of gcode based machine.

    the photon doesn't look as good...
  17. http://www.buildyourownsla.com/forum/viewtopic.php...

    http://www.buildyourownsla.com/forum/viewtopic.php?t=97
    there you go :-)
    creation workshop will run under mono on linux.
    I have no clue what that means - but it's in the link above :-)
    ...
  18. yep. I usually suggest you get simplify 3d,...

    yep.
    I usually suggest you get simplify 3d, which has linux versions.
    But check the wanhao software first - their fdm slicer is pretty good and there are differences in what you can print with a...
  19. yep was going to suggest getting a cheap fdm as...

    yep was going to suggest getting a cheap fdm as well.
    It's not that they are bad - fdm is an amazing technology and the sheer variety of filaments makes it an extremely useful thing to have.
    But...
  20. coule of points. fdm at 0.02mm layer height -...

    coule of points. fdm at 0.02mm layer height - forget it. that's fifty layers per mm - you might manage one print a week. Plus I honestly do not believe any lower range fdm machine can accurately do...
  21. what printer, slicer setting, print and bed...

    what printer, slicer setting, print and bed temperatures and speeds and what material (filamet type) you are using :-)
    Oh yeah and what surface you are printing on :-)
  22. Replies
    9
    Views
    368

    interesting - you using 60x20 strut ?

    interesting - you using 60x20 strut ?
  23. Replies
    5
    Views
    398

    yes we know it's celsius - but are you sure it's...

    yes we know it's celsius - but are you sure it's pla ?

    Unusual for pla to be printed above 230.
    The only pla i have that prints best 230-240 is the new ULtra with nano-diamonds. And that's...
  24. Replies
    5
    Views
    1,856

    sounds like you bought a dud one. Check the...

    sounds like you bought a dud one.

    Check the wiring, often a cable gets loose of 3d printers.

    I can't find any listing for this printer on ebay :-)
  25. Replies
    2
    Views
    360

    can't you just look at the receipt for the...

    can't you just look at the receipt for the printer ?
    I just don't understand why you don't know what printer you bought.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4