Close



Dig deeper, search our News website




Search:

Type: Posts; User: martinav

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    5,642

    I have a lot of dribbly too. Any way to fix this...

    I have a lot of dribbly too. Any way to fix this also?
  2. Replies
    5
    Views
    5,642

    Hmm, Well it actually did worse that time on...

    Hmm,

    Well it actually did worse that time on the rough side. You can see the two hole starts that popped off.

    Yes, I do wipe with an alcohol soaked paper towel, and do a fast level EACH...
  3. Replies
    5
    Views
    5,642

    Oh, my z is -0.05. Anything less (as in closer...

    Oh, my z is -0.05. Anything less (as in closer to zero) and adhesion is less than aweful.
  4. Replies
    5
    Views
    5,642

    A little help with first layer

    I have never had solid first layer performance. I have had some reasonable success, but I always feel like the finished product pops off a bit too easy. Now that I have a print that has several...
  5. Yes i level every time so its not a question. I...

    Yes i level every time so its not a question. I did normal manual first to set the 3 spinners, then quick automatic before each print. Im using the qidi slicer to slice and print. I never had a...
  6. Well, i actually have a finished print. Even...

    Well, i actually have a finished print. Even with the PEI, i can take the model with just two fingers, and barely give it a little tweak ant i pops off easily. i still feel like is way too easy. i...
  7. Actually, orientation and such is so far down the...

    Actually, orientation and such is so far down the road. I'm just trying to get a good first layer that will stick worth a damn.

    Yes to the open top.

    I stole the model from thangs.com. I...
  8. @Bikeracer2020,I am about to chuck this thing out...

    @Bikeracer2020,I am about to chuck this thing out the window. I have viewed so many videos, and such and nothing stick to the bedplate. Not even new ones. I have tried textured and PEI. I ended...
  9. Replies
    4
    Views
    3,026

    Yes, I found the videos. Thanks for that...

    Yes, I found the videos. Thanks for that detail.Come to find out, this was the easy problem. I cant get a damn thing to stick to any bedplate I put in it. Even new ones. New thread coming. ...
  10. Replies
    3
    Views
    2,704

    I guess nobody has this problem, or doesnt care.

    I guess nobody has this problem, or doesnt care.
  11. Replies
    3
    Views
    2,704

    BTW, address pings just fine. QIDI print doesnt...

    BTW, address pings just fine. QIDI print doesnt find it.
  12. Normal one. But i found the issue. The extruder...

    Normal one. But i found the issue. The extruder was not screwed to the gantry. All 5 screws were not engaged. Im surprised the tbing leveled and actually printed two models. While rough... they...
  13. Replies
    3
    Views
    2,704

    Qidi x-cf pro network issues.

    I first connected my printer to a wired network, and it seemed ro work great for a few days. Qidi print found it no problem. After a few days, i had to refresh in qidi print to find it, but it...
  14. Replies
    4
    Views
    3,026

    The dust looks to be coming from the cover...

    The dust looks to be coming from the cover dragging on the gantry as it traverses. I didnt notice this when i started prints, and i didnt even have the print fail. It finished a 10hr print like...
  15. Replies
    4
    Views
    3,026

    Qidi x-cf pro head cover dragging.

    Help! What do i do about this? I have not had it apart yet. Only done 2 prints.

    *UPDATE*

    I took the cover off, and it looks like these top 2 screws are not engaged. Actually they look too...
  16. First print on 'new' (used) Qidi x-cf pro. tips please!!

    Here is my first go at 3dbency. It took quite a few level test prints to get PLA to stick at ALL. I ended up doing a -0.15 Z offset that seems to have got me going. However, even with that, it...
Results 1 to 16 of 16