Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 30 minute(s) ago.

  1. Replies
    2
    Views
    7,104

    Hello been looking to see if there was anything I...

    Hello been looking to see if there was anything I could do to help you.

    I found the following information you might be well to read.

    Aquila X3 bed probe not working in Marlin/MRiscoCProUI
    ...
  2. Replies
    5
    Views
    11,542

    I need to try a Magnetic build plate one of these...

    I need to try a Magnetic build plate one of these days.
  3. Replies
    1
    Views
    2,958

    If you flashed your firmware then in order to...

    If you flashed your firmware then in order to figure out what went wrong you will need to post at least the configuration.h and configuration_Adj.h files.

    This way we can see what is going on,...
  4. Replies
    2
    Views
    7,104

    Took a quick look using google found this hope...

    Took a quick look using google
    found this hope it helps

    Here

    The code looks almost exactly like startup code on my Hictop 3DP11/12's.
    My Hictop which is almost exactly the same as an Ender 3...
  5. Replies
    7
    Views
    9,009

    I know that the Extruder stepper motor will not...

    I know that the Extruder stepper motor will not move filament until the Hotend is up the temp.

    Though we need to determine if the stepper motor is actually moving.
    Some how by hand or stepper...
  6. Replies
    7
    Views
    9,009

    I 3D Printed this nozzle box 19439 19440...

    I 3D Printed this nozzle box

    19439

    19440

    I found on t https://www.printables.com/model/154769-nozzle-box

    This was a fun project an as you can see turned out really good, an is more than...
  7. Replies
    7
    Views
    9,009

    I have a similar 3D Printer and had a block so...

    I have a similar 3D Printer and had a block so bad that decided to replace everything.

    Throat w/PTFE throat
    Heater Block
    Nozzle
    12/24volt Heater (as I have 12v and 24V 3D Printers)
    Thermister...
  8. Replies
    7
    Views
    9,009

    Yes they are called a Sock Official Creality...

    Yes they are called a Sock

    Official Creality Ender 3 V2 Neo Silicone Sock
  9. Replies
    2
    Views
    4,219

    Have no ideal what you mean by derugulated. ...

    Have no ideal what you mean by derugulated.

    However I have just had a similar problem after several hours of troubleshooting I have learned that the SD card was causing the problem.
    I tested the...
  10. Replies
    1
    Views
    5,499

    hello Use 210C for Nozzle and 55C for Bed temp...

    hello

    Use 210C for Nozzle and 55C for Bed temp with PLA+.
    ALWAYS use a raft
  11. When I have similar problems you are describing,...

    When I have similar problems you are describing, I find that the PTFE tubing has deformed and needs to be replaced.

    Pictures attached. Thought this may be causing your problems.

    19431
  12. Replies
    5
    Views
    11,542

    I have been getting away with Printing ABS with a...

    I have been getting away with Printing ABS with a Bed temp of 96C and Print temp of 232C by placing the 3D Printer in a enclosure.
    This keeps breezes away causing my models to warp.
  13. Below is a tutorial on how to fix, ...

    Below is a tutorial on how to fix,

    https://www.youtube.com/watch?v=FqHXkmRoLXA
  14. Replies
    5
    Views
    11,542

    Yes Magnets do get old. And If Magnets Get...

    Yes

    Magnets do get old.
    And
    If Magnets Get Very Hot or Cold
  15. My Home Made Hotend

    My hot end started factory with a nozzle screwed into the Heat block then the throat screws into the other side of heat block this in turn slides into the top heat sink.

    This did not work...
  16. Replies
    2
    Views
    6,973

    In my Slicer Software there is an option to...

    In my Slicer Software there is an option to randomize location of seam to virtually make it invisible.
  17. I know the IC is bad and a couple other...

    I know the IC is bad and a couple other components though decided my time was worth more than the cost of a controller board that could be programmed to take its place.
  18. Replies
    3
    Views
    2,714

    Would like more information on the position of...

    Would like more information on the position of the model while 3D Printing.

    Though without any further information, i suspect that the area where the seam is located may not have a friction free...
  19. Replies
    8
    Views
    6,315

    The last lines of my startup g-code is always in...

    The last lines of my startup g-code is always in the Slicer

    M420 S1 ; Bed Leveling turned On
    M106 P1 S128 ; P1 = 2nd Fan set 50% Speed
    M220 S32.000000 Starting print speed
  20. Replies
    2
    Views
    2,620

    We read here you have a SN04 Proximity sensor, It...

    We read here you have a SN04 Proximity sensor, It would help if you stated what 3D Printer you have.
    A few pictures of your 3D Printer could also be helpful if they show optional hardware.
  21. Replies
    8
    Views
    6,315

    It appears you are doing every thing in the...

    It appears you are doing every thing in the correct order.

    Leveling the bed is kind of an Art until you have more experience under your belt some may fail an some will work.
    Some times you just...
  22. Replies
    1
    Views
    2,097

    I have used Cura 15.04.6 forever and have never...

    I have used Cura 15.04.6 forever and have never had a problem,
    Though to get better prints I now use Prusaslicer mostly newest version though all work fine for me.

    If you post STL files will...
  23. IS does not happen often though It could be that...

    IS does not happen often though It could be that you need to initialize your printer to factory defaults.
  24. Replies
    9
    Views
    27,696

    Sticky: Hello curious aardvark. My CoreXY in being...

    Hello curious aardvark. My CoreXY in being created from parts printed using this Thingiverse article. Hope it works out well.
  25. Replies
    1
    Views
    2,862

    I would start with watching this cleaning the...

    I would start with watching this cleaning the nozzle Video.

    I would start by heating the Nozzle to your last filament temp TPU an push remaining clogged TBU out with some.
    Then remember to...
Results 1 to 25 of 494
Page 1 of 20 1 2 3 4