I've tried that with no results, but thanks just the same.
I've increased the bed to nozzle to the point it wouldn't adhere to the bed anymore.
Seems to be something else going on here. I have...
Type: Posts; User: Ward
I've tried that with no results, but thanks just the same.
I've increased the bed to nozzle to the point it wouldn't adhere to the bed anymore.
Seems to be something else going on here. I have...
I guess this one has everyone stumped
Not to worry, I've never seen it either. VERY unusual
That some filament would rather cling to the print bed rather than be firmly attached to the rest of...
I have a unique issue that started recently that I haven't had before and the resolution eludes me so far.
For the sake of this issue, let's say I'm printing a rectangle that is 2 inches by 5...
I can tell you this.......
You cannot print directly onto sandpaper.
Tried it.....no adhesion at all.
Just wanting a flat finish instead of a glossy finish.
But I think sanding it will leave a powdery look?
Maybe I meant a "Satin" finish or like 1000 grit sandpaper without looking powdery?
I ...
Just wondering if anyone ever printed to get a flat final finish.
Everything I print is usually glossy finish since I print on Kapton tape primarily. PLA.
Other than getting a piece of...
Anyone know where you can get these reasonably priced?
Mine doesn't seem to want to turn the RED on anymore....and it flickers too much.
Thanks
The front and rear corner plastic supports for the X and Y axis chrome shafts split.
The right side (facing machine) Y axis rod is bent....need a new one.
The bearings are damaged it appears...
Roberts_Cliff
Thank you for the reply ! Was getting really lonely in here all alone.
In the posts above I mentioned replacing the PTFE tube in the malfunctioning extruder with a brand new one...
I'm leaning towards a power supply issue or Left Extruder hot end failing.
Anyone? Please?
Well,
I apologize to anyone in the future who finds this thread because they have the same issue. I was hoping more information might be posted.
Through further investigation, I have found that...
Ok. Thanks.
After spending considerable time on ebay, that seems to be the case.
I bought a 3D printer from Monoprice almost 2 years ago now.
(It's this one)
11147
It has about 1700 hours on it and I "think" one of the extruders has failed.
How do I determine which...
Printing with the printer shown in my Avatar.
Approximately 1,700 hours on the printer
This is a 5 hour print.
PLA
3 Processes......Process 1 = 0 - .3mm Process 2 = .3mm - 12mm ...
Ok thanks. Will use Lithium Grease next time. It's so quiet again now....I've been able to sleep again :-)
I "think" I found the source of all that noise....
This is one of the linear bearings on the side.
After adding a heavy viscosity oil (motor oil) to the rail, the noise suddenly was gone.
11139
I got this printer from MonoPrice about 1.5 years ago and it started making this noise early on but it's gotten MUCH worse.
Does anyone know what the heck is causing this noise? I'm pretty sure...
Bought this filament from an ebay seller called SpreeHut last month....
http://www.ebay.com/itm/262435735530?_trksid=p2060353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Still in the bag sealed...
Well, it "could" be that I bought a fairly inexpensive printer to begin with maybe?
I paid like $600 for my printer. If you paid much more, maybe you got a better quality unit to begin with. ...
Thanks.
Is 1,200 hours of run time a lot for a 3D printer power supply?
Is there any "average" length of time in hours of run time that a 3D printer power supply is likely to last?
Or is it totally unpredictable and totally random?
Could be the filament. It's been open for about 9 months (almost all used up now). But was stored in airtight containers with desiccant.
I took the entire dual extruder head out, thoroughly...
Follow up......
Completely disassembled both extruders.
Found very little debris in the gears but blew them out. Only a litle dust so I assume that was not the problem.
Removed the nozzles. ...
Over the last year my Flash Forge Creator X Clone has been doing great....until the last month. Now neither extruder is working.
It started with the left extruder. It was printing fine one day...
Can you tell me how you found this fault and how you fixed it?
Thanks