ah looks like you also found my post on: http://www.3dprintingforum.us/viewtopic.php?f=51&t=1754&p=16113#p16113
Perhaps, is this line already in the Marlin Config.h or am I adding it? Conversely...
Type: Posts; User: pochrist
ah looks like you also found my post on: http://www.3dprintingforum.us/viewtopic.php?f=51&t=1754&p=16113#p16113
Perhaps, is this line already in the Marlin Config.h or am I adding it? Conversely...
Using a Makerfarm Pegasus 8 which in turn is Using Marlin Firmware 1.x, trying to improve my accuracy and was wondering if there is a way to tweak my setting for the manual leveling process.When...
Using a Makerfarm Pegasus 8 which in turn is Using Marlin Firmware 1.x, trying to improve my accuracy and was wondering if there is a way to tweak my setting for the manual leveling process.When...
Using a Makerfarm Pegasus 8 which in turn is Using Marlin Firmware 1.x, trying to improve my accuracy and was wondering if there is a way to tweak my setting for the manual leveling process.
...
Just got a Flash forge guider 2 and ordered a High Temperature Extruder Kit:...
I rescued (3) maker-farm Pegasus 8 units that were originally used in in school stem class for about 2 years from the dumpster (1) was assembled by the instructor, (1) was assembled by the students...
I have been trying for months to convert my Pegasus 12 to a Dual extruder but have been hitting road blocks. I tried the Dual extruder kit on the Maker farm website and it was an exercise in...
I've been considering this for a while but find just to get the information I have pour over multiple forums, I even seen videos of people's mods in the 12" Pegasus with Lead screws but they don't go...
Well to many many viewers (104 at last count) I found that the chip that came with the kit I was told I did not need, was indeed needed and after pouring over Ramps board diagrams online I found a...
Previously I was using a Single Titan Extruder with no problems, I just recently purchased the Dual Extruder upgrade kit. Went back through the original Build Guides, Flashed the Marlin LCD and now...
I'm no stranger to upgrading firmware, but I'm going to have print out bushings to move the motor mounts further out from the frame as well to so the shaft and coupler will clear the Y axis bar its...
I'll check that when i get back to my printer.
looking at your picture I see your motor mounts and threaded rod are sturdier then what came with my kit. The clear rubber sleeves I have doubts...
Drifting is the best way to describe it (see Pic) https://drive.google.com/open?id=0B7fUnc41itGjSFJVeEZaTkhyTlRTdVBCYktHNEloVV91Z0hB
As you can see the nut is below the trap on the...
Thanks that will make it easy, I'll look on thiniverse or somewhere to see if somebody has a mount, if not I'll just whip up my own.
Is there any documentation anywhere that can point me as to where I would connect the fan to Ramps board, does it use a 3 or 4 pin connector, etc. Thanks
Do you have your fan wired to the control board or are you just controlling it manually? I know S3D has options for controlling the fan speed via the gcode.
I have been learning to use my new 3D printer since early December and have finally correctly calibrated and it and level the bed, (went for 2 weeks with poorly leveled bed and experienced failed...
I only got my printer in early December... I have been watching videos, reading posts and just absorbing info for the most part as I meander through the learning process. I have seen many videos...
That's great, way easier then blowing out the system and installing a new OS.
This is shot in the dark as I have not had to deal with USB / Com port resources issues for a while (until I got my 3D printer in December). I have no experience with Kinect or the software your...
Resolution wise the lower the number the better, but that increases time. so a 0.40mm will make a sharper print then a 0.50mm (but the 0.50mm will complete the print the print faster). Speed is also...
At this point maybe you should contact the shop you got it from and see if they can check it out..
I just ordered a 10 meter sample pack of Ninjaflex and although I have been reading other posts in other sections of this forum, I even went through this guide posted in the Filaments section:
...
OK just so we know this going in I'm new to 3D printing as well S3D, so I'm going to approach this from an IT perspective and deal with the Software and Hardware.
1) The Voltage (ie. Electricity)...
I'm guessing the far right (if i compare it to mine) is the X-axis there is a box on the Gcode page you are referring to that says "Flip build Table Axis" I would check off the box for the "X" axis....