Close



Page 7 of 24 FirstFirst ... 5678917 ... LastLast
Threads 121 to 140 of 463

Forum: RepRap Format Printer Forum

Discussion related to RepRap Format 3D Printers.

Sub-Forums Last Post

  1. Discussion related to Firmware Enhancements to Marlin.

    Forum Actions:

    Forum Statistics:

    • Threads: 50
    • Posts: 1,322
  2. Forum Actions:

    Forum Statistics:

    • Threads: 5
    • Posts: 25
  3. Discuss related to Geetech 3D Printers

    Forum Actions:

    Forum Statistics:

    • Threads: 8
    • Posts: 27
  4. Discussion related to MakerFarm Prusa and PrintrBot 3D printers

    Forum Actions:

    Forum Statistics:

    • Threads: 834
    • Posts: 10,850
  1. Sticky Thread Sticky: RepRap Community - Introduce Yourselves

    Started by Eddie, 10-08-2013 12:34 PM
    • Replies: 68
    • Views: 183,742
    12-14-2021, 04:32 AM Go to last post
  2. Sticky Thread Sticky: Show your RepRap Printers

    Started by Larry, 10-09-2013 09:06 AM
    • Replies: 61
    • Views: 204,784
    02-27-2020, 04:13 AM Go to last post
  1. Marlin Autobed Level vs. Z probe?

    Started by clearlynotstefan, 08-17-2016 09:41 PM
    • Replies: 3
    • Views: 4,361
    08-18-2016, 04:34 PM Go to last post
  2. homing X Y axis off set

    Started by weirdguy, 08-17-2016 09:36 AM
    • Replies: 4
    • Views: 2,830
    08-17-2016, 11:47 AM Go to last post
  3. incomplete layers

    Started by mazzi16, 08-12-2016 06:15 AM
    • Replies: 0
    • Views: 2,498
    08-12-2016, 06:15 AM Go to last post
  4. Angry Ramps 1.4 on Wanhao I3 thermocouple reading

    Started by Goderfer, 07-12-2016 02:26 PM
    ad597, electrical noise, problem, thermocouple, wanhao i3
    • Replies: 4
    • Views: 5,309
    08-02-2016, 09:22 PM Go to last post
    • Replies: 9
    • Views: 28,182
    07-27-2016, 04:20 AM Go to last post
    • Replies: 2
    • Views: 2,904
    07-26-2016, 05:59 PM Go to last post
    • Replies: 0
    • Views: 2,377
    07-22-2016, 03:55 AM Go to last post
    • Replies: 0
    • Views: 2,626
    07-19-2016, 09:39 PM Go to last post
  5. auto leveling crashes into bed after probing

    Started by hegel, 07-03-2016 01:06 AM
    • Replies: 3
    • Views: 2,767
    07-13-2016, 12:13 PM Go to last post
  6. Ramps 1.4 - Swapping Hotend and Heatbed relays

    Started by hernejj, 05-25-2016 06:46 PM
    • Replies: 1
    • Views: 2,762
    07-07-2016, 02:33 PM Go to last post
  7. Question for Stepper Motor Experts

    Started by Roxy, 06-27-2016 02:56 PM
    • Replies: 4
    • Views: 4,021
    07-07-2016, 02:29 PM Go to last post
  8. I have just put together my Hictop Prusa i3

    Started by Ray_, 06-28-2016 06:49 AM
    adding dual extruders i3
    • Replies: 1
    • Views: 2,756
    06-28-2016, 11:21 AM Go to last post
    • Replies: 4
    • Views: 9,426
    06-20-2016, 10:17 PM Go to last post
  9. Exclamation x homing in wrong direction

    Started by bzmotoninja83, 06-08-2016 02:15 AM
    • Replies: 1
    • Views: 4,419
    06-18-2016, 01:31 AM Go to last post
    • Replies: 6
    • Views: 4,093
    06-16-2016, 01:53 AM Go to last post
    • Replies: 0
    • Views: 2,410
    06-15-2016, 06:13 PM Go to last post
  10. Sneak peek of my new printer

    Started by CaptainObvious, 04-30-2016 11:22 PM
    • Replies: 6
    • Views: 4,901
    05-31-2016, 12:41 PM Go to last post
  11. Question Which Control Board to Buy!? Too many choices!

    Started by dvseliteus, 04-28-2016 11:53 AM
    • Replies: 5
    • Views: 4,304
    05-29-2016, 04:45 PM Go to last post
  12. New guy here

    Started by bzmotoninja83, 04-20-2016 02:42 AM
    • Replies: 16
    • Views: 11,897
    05-29-2016, 12:57 AM Go to last post
  13. E3D installed in an unknown printer

    Started by wjuniorbr, 05-24-2016 09:54 PM
    • Replies: 2
    • Views: 3,463
    05-27-2016, 12:51 AM Go to last post

Page 7 of 24 FirstFirst ... 5678917 ... LastLast

Forum Information and Options

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data