Close



Search:

Type: Posts; User: DaveB

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    59
    Views
    3,402

    Sorry if I missed this previously, PLA?

    Sorry if I missed this previously, PLA?
  2. Replies
    7
    Views
    487

    Are the solder joints heating up and causing the...

    Are the solder joints heating up and causing the heatshrink tubing to shrink while the printer is IN USE? Or is this happening during your soldering process, or just due to proximity of the joints...
  3. Replies
    15
    Views
    771

    Yeah... I think that's gonna depend upon what...

    Yeah... I think that's gonna depend upon what you were cooking in the smoker. I've seen coffee flavored filament, and I could probably get behind some kind of BBQ aroma, but not so sure I could...
  4. Replies
    15
    Views
    771

    I'm trying something new for my dry box revision...

    I'm trying something new for my dry box revision 2. My initial version had a suspended shaft upon which the rolls of filament were mounted. It works great, but is a complete pain whenever you want...
  5. Replies
    7
    Views
    487

    Do you have a volt meter? With the machine...

    Do you have a volt meter?

    With the machine off & unplugged, and the heater unplugged from the motherboard, start by measuring the heater element to see if it is still intact. Measure the ohms...
  6. Replies
    15
    Views
    771

    This is the one I saw at Sam's Club. It may be...

    This is the one I saw at Sam's Club. It may be larger than desired.
    https://m.samsclub.com/ip/sterilite-80-qt-gas-sterlt-80q-gsket-box/prod21161032

    The one from Target holds 4 spools of...
  7. Replies
    15
    Views
    771

    That's great! Better luck than I experienced...

    That's great! Better luck than I experienced with my poppin' ABS. FYI, the "Sterilite" box claim to fame is the very compressible foam that runs around the entire lid joint. It does a...
  8. Replies
    15
    Views
    771

    The best approach is prevention. Don't let it...

    The best approach is prevention. Don't let it get wet in the first place. Lots of folks take a dry box approach, you might look that up on Thingiverse. Most use desiccant, but there are also some...
  9. Replies
    103
    Views
    5,393

    Oxi, Any more pix or info on the "X-One2"?

    Oxi, Any more pix or info on the "X-One2"?
  10. Replies
    103
    Views
    5,393

    Using S3D you hit a save button and it walks you...

    Using S3D you hit a save button and it walks you through a widget to specify the file location. Within the S3D configuration settings that control how to "post process" the GCODE that it generates,...
  11. Replies
    103
    Views
    5,393

    Sorry, I use Simplify 3D. It performs the X3G...

    Sorry, I use Simplify 3D. It performs the X3G conversion by invoking GPX. No idea what's going on under the covers.
  12. Replies
    103
    Views
    5,393

    Please take and publish more pictures. This is...

    Please take and publish more pictures. This is the first and only info on this new version from QiDi that I've been able to find.
  13. Replies
    4,058
    Views
    648,709

    Sticky: New QiDi "X-One-2" http://imgur.com/DaTcriN.jpg...

    New QiDi "X-One-2"
    http://imgur.com/DaTcriN.jpg
    It's now an enclosed chamber.
    Nothing on QiDi websites, no additional info from QiDi support. This is all I can find so far.
  14. Replies
    103
    Views
    5,393

    I've got the QiDi Tech 1, no personal hands-on...

    I've got the QiDi Tech 1, no personal hands-on time with an X-one. Tech 1 uses X3G, not GCODE. There is usually a X3G converter application (like thingiverse GPX...
  15. Replies
    439
    Views
    22,780

    Loaded & sliced no problems. Maybe you've got...

    Loaded & sliced no problems. Maybe you've got some bad memory or a broken copy of S3D?
  16. Replies
    103
    Views
    5,393

    IF you are interested in using the Toshiba...

    IF you are interested in using the Toshiba FlashAir SD card (version 3) with the QiDi, I can vouch for the Toshiba cards functionality with the QiDi Tech 1 and S3D under Windows. Here is a link for...
  17. Replies
    103
    Views
    5,393

    Simplify 3D is excellent, and is rumored to have...

    Simplify 3D is excellent, and is rumored to have an update due out soon.
  18. Replies
    103
    Views
    5,393

    Get the QiDi

    Get the QiDi
  19. Replies
    4,058
    Views
    648,709

    Sticky: Just got a tool that works unbelievably well for...

    Just got a tool that works unbelievably well for trimming chaff or sharps off the edges of prints. I had used them on aluminum chassis openings after nibbling away a few eons ago and forgotten how...
  20. Replies
    4,058
    Views
    648,709

    Sticky: For whatever reason, the power supply fan on my...

    For whatever reason, the power supply fan on my QiDi is very quiet. Only the fan that was cooling the stepper motor driver modules was noisy.
  21. Replies
    4,058
    Views
    648,709

    Sticky: Finally replaced that darn noisy fan inside the...

    Finally replaced that darn noisy fan inside the QiDi.
    Here is how I did it: https://www.thingiverse.com/thing:2379468
  22. Replies
    76
    Views
    15,092

    I have been using the Toshiba Air card setup with...

    I have been using the Toshiba Air card setup with my QiDi for about a year now. I love it. It has been rock solid. HOWEVER, I have one more gold plated caveat to add to the list of Toshiba Air...
  23. Replies
    20
    Views
    5,392

    BoozeKashi: I have a gas oven that poorly...

    BoozeKashi: I have a gas oven that poorly regulates temps near 100C, so I have a developed a different approach. I put my finished pieces into a pot of water and boil them for 5 or 10 minutes. For...
  24. Replies
    4,058
    Views
    648,709

    Sticky: Hey W, did you ever receive and install the...

    Hey W, did you ever receive and install the multi-color /filament options for your Prusa? If so, how does that work?
  25. Replies
    4,058
    Views
    648,709

    Sticky: FYI Here are some additional clues about S3D...

    FYI Here are some additional clues about S3D functions that I got from them.

    https://forum.simplify3d.com/viewtopic.php?f=8&t=1959
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4