Close



Search:

Type: Posts; User: TTVert

Search: Search took 0.00 seconds.

  1. Can't hurt to try at least. Thanks Dave

    Can't hurt to try at least.

    Thanks
    Dave
  2. LOL well I'll maybe look into bracing this thing,...

    LOL well I'll maybe look into bracing this thing, not that that'd cause this.

    Dave
  3. Thanks. So those vertical lines are not normal? ...

    Thanks. So those vertical lines are not normal? I thought those were normal but I'm new to 3D printing.

    Dave
  4. Maker select v2, weird pattern in prints around round standoffs (Pic inside)

    I'm not sure exactly what is causing this but I played w/ layer height and it didn't change the effect. It isn't a huge deal to me but I'm just curious if this is an indication of something I need...
  5. For some odd reason there were no supports under...

    For some odd reason there were no supports under those. it seems one side it printed fine as far as the radius goes the other it just botched. I have it set to support type everywhere and it does...
  6. I tried to clean it, i tried to use blue 3M tape...

    I tried to clean it, i tried to use blue 3M tape and I've also tried the pad that came w/ the printer which worked flawlessly before. From what I've read I want .1mm between the printhead and...
  7. Anyone care to take a look at a pic of sagging and give input?

    The stringing you see is just remnants of the support I was using

    Maker Select 3D
    PLA 1.75mm
    .4mm nozzle
    .20mm layer height
    .8mm shell thickness
    1.2mm Bottom/top thickness
    10% fill density...
  8. Does this appear to just be an adhesion propblem?...

    Does this appear to just be an adhesion propblem? Maybe not something w/ my height, feed rate, etc? What If I increase bed temp to say 70 or 80?

    Dave
  9. Out of nowhere maker select 3d print is curing in middle

    It was printing perfect for about 10 prints and then this (See pics) I'm beyond frustrated at this point. I'm printing w/ PLA. I'm using the bed cover piece that came w/ the printer. I've tried re...
  10. Cura 15.0.4.6 end code question, bed never homes

    So basically I'm using a Maker Select 3D and I've got the start Gcode working well however when I print via usb (I think from SD it does it also) I have to hit cancel print even though the print is...
  11. I'm using cura 15.04.6. (I print via usb and 2.3...

    I'm using cura 15.04.6. (I print via usb and 2.3 and 2.4 won't support my printer :( ) I didn't see an option to set brim specs other than "brim line amount" What is the purpose of a skirt, to...
  12. Thank all. Yes it does work a treat. I've...

    Thank all. Yes it does work a treat. I've printed a few skits and brims now. I'm now working on an issue where the brim is a bit hard to detach from the base of the print.

    Dave
  13. Thanks it appears that it's just a printer config...

    Thanks it appears that it's just a printer config where the start/end gcode is. I added it in there and I appears to be added to all my prints. Can someone confirm I am doing the correct thing here...
  14. bottom most layer 1/2 mm wider than all other layers

    My thought process was the bed may be too hot and allowing the filament to settle a bit so I lowered it from 70 to 60 but it didn't help much. The item I am printing is 16.40mm on all layers except...
  15. Sorry is the skirt the dotted line or the purple?...

    Sorry is the skirt the dotted line or the purple? I believe either would be fine. I think i understand better now after some more reading. It seems you may be able to set a global printer config that...
  16. New to 3D printing, how can i print a test line before prints?

    It seems that none of my prints have that test line and I don't know if that is SOP for 3D printing but it seems that it somewhat cleans the print nozzle and allows for a clean base. I think it's...
Results 1 to 16 of 16