Close


Flash Forge Inventor




Search:

Type: Posts; User: number40Fan

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    27
    Views
    434

    I'll try printing it with the settings I use and...

    I'll try printing it with the settings I use and go from there.
  2. Replies
    27
    Views
    434

    Oh, I see you are giving me the .x3g file and not...

    Oh, I see you are giving me the .x3g file and not the .STL, but layer height would be nice. I have different height adjustments when leveling the bed for different layer heights.Edit: I see .2...
  3. 93% in on the big balloon and there is a touch of...

    93% in on the big balloon and there is a touch of wobble. Slow her down a bit more....maybe...maybe.
  4. Replies
    27
    Views
    434

    I think I do have PLA in the left. Make it right...

    I think I do have PLA in the left. Make it right and what layers/print height are you using?
  5. Nice, huh? :D Something about the steps per...

    Nice, huh? :D Something about the steps per minute, 20 tooth belts, yada yada. but it made their prints better.

    To change the filament on the fly, I just cut the filament going in about an inch...
  6. Replies
    27
    Views
    434

    Attach your file and I'll throw it at my Qidi and...

    Attach your file and I'll throw it at my Qidi and see what happens.
  7. Printing a larger version of the hot air balloon,...

    Printing a larger version of the hot air balloon, 200mm high, and I just went and looked and it isn't holding it up high enough for the outer edges. Worked great for the dragon that was 130mm high,...
  8. http://i67.tinypic.com/rky3ia.jpg How do you...

    http://i67.tinypic.com/rky3ia.jpg

    How do you have yours set up? It points towards the back strut and holds the wire loom out or more importantly, up. Gives more room for those taller prints.
  9. http://i63.tinypic.com/2zp2mab.jpg

    http://i63.tinypic.com/2zp2mab.jpg
  10. Attaches to the frame right where the wires come...

    Attaches to the frame right where the wires come out on the Y strut.
  11. Replies
    18
    Views
    484

    If it is like the Qidi, which is a clone, you hit...

    If it is like the Qidi, which is a clone, you hit the left arrow while it is printing and then start scrolling down until you find Change Temperature. Hit select and then move it up and down. Can't...
  12. You want to attempt this wire holder? It is...

    You want to attempt this wire holder? It is working pretty good for me. Moving back and forth with the wiring. Need to rotate on the X -90.
  13. The lights are for the printer. Need to light up...

    The lights are for the printer. Need to light up under the nozzle.

    If the three outside points are the same height, then the middle should be too. Only if you had some wonky surface, would it...
  14. Someone said...."Let there be light!" ...

    Someone said...."Let there be light!"

    http://i67.tinypic.com/20h3jx5.jpg

    Next project.
  15. .16. Weird number, but I was also testing...

    .16. Weird number, but I was also testing something I read about stepper motors and their ability to move between steps accurately at different layer heights.
  16. http://i64.tinypic.com/2qb6s9d.jpg This came...

    http://i64.tinypic.com/2qb6s9d.jpg

    This came out nice!!
  17. Replies
    27
    Views
    434

    All of those are just the beginning prime of the...

    All of those are just the beginning prime of the print and won't affect the actual print.
  18. Replies
    6
    Views
    166

    You could swap all of the connector from the left...

    You could swap all of the connector from the left to the right on the motherboard and run a print from the left head, which will be the right now and see how it goes. I think I read about a way to...
  19. http://i66.tinypic.com/w06fs0.jpg New rods...

    http://i66.tinypic.com/w06fs0.jpg

    New rods done. Made a mess of the epoxy glue, hot glue, but they work and boy do they hold tighter.

    What do you really think about the bed springs? Do you...
  20. Awesome setup. Nope, wires don't matter. Also,...

    Awesome setup. Nope, wires don't matter. Also, to make sure you get the most accurate measurement, have to piece of the switch that touches the bed inline with the nozzle.

    Edit: I printed it...
  21. http://i63.tinypic.com/2r3vwvl.jpg This is...

    http://i63.tinypic.com/2r3vwvl.jpg

    This is what I need to print for the carriage adapters. How the heck am I going to do this? I need the cups pointing up for the best print.
  22. Wow, I didn't notice before that the Carbon Fiber...

    Wow, I didn't notice before that the Carbon Fiber tubes you linked too were 1 meter long. That is a good price, heck great price. With the rod ends I am making, you could get three of the arms with...
  23. The hot glue is just temporary, so I can remove...

    The hot glue is just temporary, so I can remove the balls and reuse them.

    Regular glass with a spritz of hair spray.
  24. Replies
    6
    Views
    166

    What type of filament and temp? Slicer? Beer...

    What type of filament and temp? Slicer? Beer that you enjoy?
  25. Hey, Mr. Aardvark. I'd like to give a big 'ole...

    Hey, Mr. Aardvark. I'd like to give a big 'ole hug to you. Tell you thanks. And this one is for you. Enjoy!


    http://i63.tinypic.com/4v5qhs.jpg
Results 1 to 25 of 265
Page 1 of 11 1 2 3 4