Close



Search:

Type: Posts; User: spegelius

Search: Search took 0.00 seconds.

  1. Well to me it starts to look like the board is...

    Well to me it starts to look like the board is defective, might be that there's bad connection somewhere and the motor cannot move as one of the phases doesn't work (or something...). Of course you...
  2. Ok so it seems that the problem is with the...

    Ok so it seems that the problem is with the Z-drivers. MEasuring the amps is possible, but usually it's just easier to check the Vref, as you already have done. 0.84v itself doesn't tell much, it...
  3. Replies
    20
    Views
    6,429

    I couldn't get the PLA working properly, jams too...

    I couldn't get the PLA working properly, jams too easily. If I heat up the hotend, extrude stuff a bit and let it just sit there like 10 seconds or more, it's already jamming. Works when printing...
  4. Usually you can't move extruder before hotend is...

    Usually you can't move extruder before hotend is heated; this is a safety feature as extruding to unheated hotend might break things.

    For Z-axis, you could try:
    - connect only one motor at a...
  5. Replies
    20
    Views
    6,429

    Hmm,if I remember correctly, the non-printed...

    Hmm,if I remember correctly, the non-printed parts cost about 170 eur. I had most of the crews already, but buying those isn't a big cost. I didn't try to find the cheapest parts, because getting el...
  6. Replies
    20
    Views
    6,429

    Alright, you make 3rd active, or at least...

    Alright, you make 3rd active, or at least interested, person regarding Dollo :). Ok so I'll try to give some information about how to go on about building one:


    If you are going to print the...
  7. To help with adhesion to the bed. Also part...

    To help with adhesion to the bed. Also part cooling fan is usually off for the first layer.

    If your particular setup doesn't need this, this behaviour can be changed of course.
  8. If the printer accepts simple g-code files, you...

    If the printer accepts simple g-code files, you could try something like this:

    M109 S200 ; set and wait hotend temp. Adjust S200 to fit your needs
    G1 E30 F50; tell extruder to move30mm of...
  9. Replies
    20
    Views
    6,429

    For the firts time I've actually been just using...

    For the firts time I've actually been just using Dollo, instead of building or tweaking it. I've been printing these containers in hopes that I can get at least some of my stuff organized. In current...
  10. Replies
    3
    Views
    493

    First pic: - seems like a consistent deviation...

    First pic:
    - seems like a consistent deviation in axis (Y or X). Check the axis movement for small bumps.

    Second and third pic:
    - I saw similar problems when printing PLA with clone E3Dv6...
  11. Replies
    20
    Views
    6,429

    Hmm it seems Dropbox has changed things and...

    Hmm it seems Dropbox has changed things and previous links aren't working anymore. Well the link to the Dollo-folder works: https://www.dropbox.com/sh/g2z5027vm3v3h9x/AACTkwrC0idOvVPVvJxo-6MXa?dl=0
    ...
  12. Replies
    11
    Views
    1,396

    Thanks, Prusa i3 MK2 does a fairly good job, I'm...

    Thanks, Prusa i3 MK2 does a fairly good job, I'm very pleased with the printer. With PLA, cooling is required if you want good details. I don't know how much cooling affects layer adhesion, but I've...
  13. Replies
    11
    Views
    1,396

    I printed the head and as expected, the result...

    I printed the head and as expected, the result isn't perfect, but good enough for me. Should be fine with bit of post processing.

    Sliced with KISSlicer, 0.1 mm layer, 0.45 mm extrusion width, 2...
  14. Replies
    11
    Views
    1,396

    Is the whole print a stringy mess? If so, sounds...

    Is the whole print a stringy mess? If so, sounds weird because lowering the layer height should improve quality. Then again not every printer and their settings behave similarly...

    Stringy mess...
  15. Replies
    11
    Views
    1,396

    You could try lowering layer height to 0.1 mm or...

    You could try lowering layer height to 0.1 mm or even lower if possible. Also if you print with more than one perimeter, print outer perimeter last, it should produce better results.

    If you use...
  16. Replies
    20
    Views
    6,429

    Testing the parts stabilizer parts:...

    Testing the parts stabilizer parts:
    https://dl.dropboxusercontent.com/u/45385735/3dprinting/Dollo/2017-02-16%2021.30.47.jpg...
  17. Replies
    21
    Views
    2,906

    As far as I know, you need an ATX power supply if...

    As far as I know, you need an ATX power supply if you want to be able to turn printer on or off. Here's an Instructable about it:...
  18. Replies
    20
    Views
    6,429

    Bed carraige installed and much more stable that...

    Bed carraige installed and much more stable that the previous iteration:

    https://dl.dropboxusercontent.com/u/45385735/3dprinting/Dollo/2017-02-13%2021.39.20.jpg

    Also started modeling and...
  19. Replies
    20
    Views
    6,429

    New bed carriage part in the making, lots stiffer...

    New bed carriage part in the making, lots stiffer that previous iteration. Also switched to printed bolts

    https://dl.dropboxusercontent.com/u/45385735/3dprinting/Dollo/2017-02-05%2014.48.24.jpg...
  20. Replies
    20
    Views
    6,429

    Results of the Benchy print: - stringing because...

    Results of the Benchy print:
    - stringing because of too little retraction as I needed to switch to longer bowden tube after extending the axes
    - few skipped steps in Y-axis at the lowest layers....
  21. Replies
    20
    Views
    6,429

    Finally got to expanding my Dollo printer in X...

    Finally got to expanding my Dollo printer in X and Y axes (sorry about the bad quality, Jolla C doesn't have very good camera...). Needed to print lot of extension parts and ties, also some of the...
  22. Replies
    20
    Views
    6,429

    Some finetuning to Z-axis rails and getting quite...

    Some finetuning to Z-axis rails and getting quite good results:
    https://dl.dropboxusercontent.com/u/45385735/3dprinting/Dollo/2016-12-22%2020.00.58.jpg...
  23. Replies
    20
    Views
    6,429

    Yesterday I printed a 40cm model:...

    Yesterday I printed a 40cm model: http://www.thingiverse.com/thing:157102 Z scaled 200%. It went better than expected, my worries about the plastic frame giving too much was unwarranted, at least...
  24. Replies
    20
    Views
    6,429

    Been creating models and printing stuff quite a...

    Been creating models and printing stuff quite a lotfor Dollo so here's some updates about my build:
    - created a model to attach PSU underneath the frame
    - adapter for RAMPS box mount to Dollo bow...
  25. Replies
    20
    Views
    6,429

    I've been printing and hacking away with the...

    I've been printing and hacking away with the design for some time and I've got a build that works quite well. The quality isn't very good at the moment but getting there. The design itself is not the...
Results 1 to 25 of 25