Close



Search:

Type: Posts; User: jfkansas

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3,996
    Views
    461,400

    Sticky: 3 years on original wiring like this. The wires...

    3 years on original wiring like this. The wires are taped to the side panel.

    10377
  2. Replies
    3,996
    Views
    461,400

    Sticky: I haven't ran PLA at all. It should be fine, I...

    I haven't ran PLA at all. It should be fine, I have like 1 roll of purple I guess I could try sometime. I think it is because of the inconsistency of PLA temps. ABS is almost always good at 235 or...
  3. Replies
    3,996
    Views
    461,400

    Sticky: MicroCenter isn't in all cities. It is a smaller...

    MicroCenter isn't in all cities. It is a smaller privately owned electronics chain. Nerd paradise. Kind of like a Best Buy, but tons better and actually decent and competitive prices.
  4. Replies
    3,996
    Views
    461,400

    Sticky: Lol, I stick with Micro Center stuff for now. It...

    Lol, I stick with Micro Center stuff for now. It is good. I like Esun filament from Amazon too.
  5. Replies
    3,996
    Views
    461,400

    Sticky: No it is a 24v power supply... You could regulate...

    No it is a 24v power supply... You could regulate an output down though. Amp wise it depends on what PS it has but 1 amp shouldn't be a problem especially after everything is heated up. The power...
  6. Replies
    3,996
    Views
    461,400

    Sticky: The only problem with getting the MicroSwiss...

    The only problem with getting the MicroSwiss conversions for the QIDI is the thermal tubes don't fit very well in the Cooling bar. The tubes on the Qidi are just a little bigger, so the Microswiss...
  7. Replies
    9
    Views
    681

    Hmm, that isn't a cable issue, might be cooling...

    Hmm, that isn't a cable issue, might be cooling related.
  8. Replies
    9
    Views
    681

    Pics help. It could be a partially broken stepper...

    Pics help. It could be a partially broken stepper cable. Is there a clear step where the printing moves to the left? It is good to reroute your X cables to something like this.

    10261

    This is on...
  9. Replies
    3,996
    Views
    461,400

    Sticky: I don't even have Makerware installed anymore so...

    I don't even have Makerware installed anymore so hard to help more. S3d is 100 times better and all those flow controls are directly exposed to the end user. The latest versions of Makerware 3 and up...
  10. Replies
    3,996
    Views
    461,400

    Sticky: Looks like you are extruding way too much...

    Looks like you are extruding way too much plastic. Makerware software is kind of a PITA to change that but it is possible. You will have to find the JSON profile that you are using and up the...
  11. Replies
    3,996
    Views
    461,400

    Sticky: Yep sure do. It costs a little to do it but have...

    Yep sure do. It costs a little to do it but have sent several orders there in the past.
  12. Replies
    3,996
    Views
    461,400

    Sticky: A few of the early adopters go a discounted price.

    A few of the early adopters go a discounted price.
  13. Replies
    3,996
    Views
    461,400

    Sticky: Ahh, I got my guys mixed up. Another guy with a...

    Ahh, I got my guys mixed up. Another guy with a user name beginning with C ordered one. lol

    Send me a PM if you are interested still.
  14. Replies
    3,996
    Views
    461,400

    Sticky: Thanks, did you ever get yours installed? lol

    Thanks, did you ever get yours installed? lol
  15. Replies
    3,996
    Views
    461,400

    Sticky: Yes, it has always had the 2 wider back mounts. A...

    Yes, it has always had the 2 wider back mounts. A potential customer suggested having the 2 front ones added in case someone didn't want to use the wider mounting. It was an easy add and didn't cost...
  16. Replies
    3,996
    Views
    461,400

    Sticky: Nice, I just launched mine this week. ...

    Nice, I just launched mine this week.

    http://store.wmdproducts.com/index.php?route=product/product&path=63&product_id=67
  17. Replies
    17
    Views
    982

    Ya I'm sure it works, just extra steps to do a...

    Ya I'm sure it works, just extra steps to do a pretty simple process. Goes against my principle of if you are spending more than 1-2 minutes to check and maybe adjust levell/gap then doing something...
  18. Replies
    17
    Views
    982

    Only the bed being heated affects bed "leveling"....

    Only the bed being heated affects bed "leveling". As it heats it expands and this tweaks/twists the platform. The nozzle being heated just affects start gap which you want to be net zero after...
  19. Replies
    17
    Views
    982

    I disagree with this. Thermal expansion of the...

    I disagree with this. Thermal expansion of the hot end is why you are setting a gap with a piece of paper or a feeler gage. It's also unsafe to be mucking around leveling with a 450 degree hot end.
  20. Replies
    17
    Views
    982

    Important notes about leveling also. After you...

    Important notes about leveling also. After you have leveled it hot, don't check level when it is cool, it will make you want to level again when cool, but will be off again when hot. You will get...
  21. Replies
    17
    Views
    982

    Did you level the bed with it heated to at least...

    Did you level the bed with it heated to at least 70-80c? There is some metal expansion that happens when heated and it tweaks the level a bit. So if it is level cold, when heated it can throw it off...
  22. Hey there, sorry about the problems. As far as...

    Hey there, sorry about the problems. As far as the problems you are having, the Newer and older versions of the Creator pro all use the same parts in the print head.

    It does sound like you have...
  23. Replies
    3,996
    Views
    461,400

    Sticky: Ya I don't get it either. And one of the little...

    Ya I don't get it either. And one of the little chunks I got was on a piece that self released after cooling. I wasn't even prying on it. All I can think is it had a previous defect in that area from...
  24. Using slurry helps, it acts like a raft or brim...

    Using slurry helps, it acts like a raft or brim if you use it right. Also you don't have to use the default support settings. Running the supports at 2 angles helps with stability, 45 and -45 is...
  25. Replies
    1
    Views
    333

    No bed is most likely not warped. You might...

    No bed is most likely not warped.

    You might have to raise the nozzle/hot end a bit to get more adjustment range.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4