Close



Search:

Type: Posts; User: wirlybird

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    248

    If your doing a test cube then anything less than...

    If your doing a test cube then anything less than 100% infill is a waste of time. Go over to the Flashforge area here and get the Sailfish manual. then find the section on calibration. It will...
  2. Thread: a Hairy Lion

    by wirlybird
    Replies
    8
    Views
    347

    I did one on my MK2. Takes some work but doable.

    I did one on my MK2. Takes some work but doable.
  3. Thread: a Hairy Lion

    by wirlybird
    Replies
    8
    Views
    347

    Looks like Wendy is a con job taking credit for...

    Looks like Wendy is a con job taking credit for stuff that isn't theirs. Very disingenuous and doesn't help anyone.
  4. Replies
    312
    Views
    255,380

    Sticky: What is the print bed? Is it the blue stuff that...

    What is the print bed? Is it the blue stuff that comes with it? If so then yes it can be tough. Glue stick may help and also letting it cool completely could help.
    What material? PLA? If so...
  5. Thread: a Hairy Lion

    by wirlybird
    Replies
    8
    Views
    347

    How odd ... the guy who made it said the printer...

    How odd ... the guy who made it said the printer is a Renkforce RF1000. Something doesn't smell right.
  6. Replies
    3,912
    Views
    402,791

    Sticky: Agreed on the leakage and Micro-Swiss addresses...

    Agreed on the leakage and Micro-Swiss addresses leakage in their instructions.
  7. Replies
    6
    Views
    300

    Check for free movement and lube it if needed but...

    Check for free movement and lube it if needed but with like 3 in 1 oil or something lite. Also try cutting the print speed way back to maybe 2000mm/min.
  8. Replies
    6
    Views
    300

    Yes they are, I just got a notification on that1

    Yes they are, I just got a notification on that1
  9. Replies
    2
    Views
    206

    Could be S3D's thin wall behavior. Sometimes...

    Could be S3D's thin wall behavior. Sometimes dropping the nozzle size setting from .4 to .39 can force it to slice areas that otherwise it doesn't or at least let you know so you can fix it in the...
  10. Replies
    7
    Views
    537

    Check out thingiverse.com and do some searches...

    Check out thingiverse.com and do some searches for your printer to see if people are building anything. Also google to see if it is a clone of another printer. Usually then you can swap in part etc.
  11. Good and not good! We at least can say the...

    Good and not good! We at least can say the profile is probably not the cause. So we look elsewhere.
  12. Odd. I would try then under help to reset back...

    Odd. I would try then under help to reset back to all defaults. This can help clean up anything that may have gotten out of wack. Then check for updates and after that run the configuration wiz...
  13. yea, I saw that. Just not really sure what it...

    yea, I saw that. Just not really sure what it could be but figuring out which profile is good is a starting point!
  14. If it still gives you trouble I would email S3D...

    If it still gives you trouble I would email S3D support and ask them about the profile to use.
  15. Yes. Try the Flashforge Dreamer profile in S3D. ...

    Yes. Try the Flashforge Dreamer profile in S3D. Check out the forums at S3D and also see this post if it helps.

    https://www.3dhubs.com/talk/thread/losing-my-mind-powerspec-ultra-3d-simplify3d
  16. What printer are you selecting in the software? ...

    What printer are you selecting in the software? I think this one is going to be a Replicator 1 (Dual) as a base, also could use Flashforge Creeator Pro. If I have the right printer!!
  17. Replies
    6
    Views
    300

    Could be a variety of things. Bad model to...

    Could be a variety of things. Bad model to printing to fast.
    I would run the model through a checker like makepritable.com to make sure it is ok.

    What was the material, temps and speeds? Was...
  18. Replies
    3,912
    Views
    402,791

    Sticky: Found a lot of spool are a little to wide for the...

    Found a lot of spool are a little to wide for the stock QIDI holders so I made new longer ones with new end caps. Work like a charm.
    ...
  19. Replies
    2
    Views
    173

    You are confusing two different things here. The...

    You are confusing two different things here. The firmware is the "software" that is on the motherboard that is in the printer. RepG and Makerware are slicers. RepG probably flashed the wrong...
  20. Replies
    3,912
    Views
    402,791

    Sticky: Got it off Amazon. Came across a couple articles...

    Got it off Amazon. Came across a couple articles and they really liked this one so I got a few. Price was ok and they plug in to recharge.
    The bins are great - ZipLock with seals on the lids.
  21. Replies
    3,912
    Views
    402,791

    Sticky: New Humidity controlled filament dry storage with...

    New Humidity controlled filament dry storage with dehumidifier. Holds 8 Rolls.


    http://i58.photobucket.com/albums/g276/wirlybird/20170114_132656_zpsvl7qzyrk.jpg
  22. Replies
    3,912
    Views
    402,791

    Sticky: Good to hear but if you selected the QIDI Tech as...

    Good to hear but if you selected the QIDI Tech as the profile it should have been set up.

    One tip. Watch the lower left for a status of saving to the SD card. Give it plenty of time to finish.
    ...
  23. Replies
    3,912
    Views
    402,791

    Sticky: All the driver does is create a port. So once...

    All the driver does is create a port. So once the driver is installed you will need to determine what port the printer picks up when plugged in and then tell S3D what port to use. The printer will...
  24. Replies
    3,912
    Views
    402,791

    Sticky: You would need to get either the last version of...

    You would need to get either the last version of ReplicatorG which is really outdated but the driver will work or go get Flashprint. Flashprint should be fine just select Flashforge Creator Pro as...
  25. Replies
    3,912
    Views
    402,791

    Sticky: Yes. I use JF's setup with Micro-Swiss all metal...

    Yes. I use JF's setup with Micro-Swiss all metal hot ends on one of my Flashforge Creator Pro's. Or go with his hot ends also I guess. I already had the hot ends when I got his cooling block and...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4