Okay so I just bought a Tronxy X5s and upgraded it, and while it gives some very nice prints, the problem is this:
Since the power supply that came with it is too weak to run the whole thing, I...
Type: Posts; User: iamthebest22
Okay so I just bought a Tronxy X5s and upgraded it, and while it gives some very nice prints, the problem is this:
Since the power supply that came with it is too weak to run the whole thing, I...
Hmm okay thanks Trakyan, it was my mother who smelled it and I went in to smell it, no burning, more like plastic smelling? yeah I would say ozone, so I'm wondering if my mother was overreacting and...
And the problem continues.... Last time I buy from this guy. I solved my extruder issues (hopefully), which was causing partial jams, and it was me being an idiot. The clone came with also a 3.0...
Thanks guys, appreciate the help, I knew red was power usually. The good thing is, and I strongly suggest you buy from Spool3d if you're in Canada, super fast shipping, and as long as you provide...
Oh I do have lots of spare USB cable, just not quite sure how to wire it to BLtouch after I cut it.
Nice thanks guys, yeah I'm considering those options, since I'm good at soldering now. But if I just want to take the fast way out, I can just buy, as mentioned before, this Arduino Uno here...
Sorry for the long no update, was sick, and then was having issues with my BLtouch not working on the Duet Wifi but working on the TEVO tornado and Cr-10 test. Finally *fingers crossed* seem to have...
Finally, It's alive!!!!! Now just waiting for E3d V6 nozzle and titan extruder and good to go. Going to be busy starting later this week as I've accepted a full time offer....
Sorry for the long delay, been busy but didn't do much until last two days. I seriously have bad luck with electronics, first PC's where I often bought defective units lol, now this, all my 5...
My wallet is super burned now that I also bought the Tronxy X5S xD. I decided to buy a 100W solder, and with my old 25W one, fixed it in 1 minute.... lol. My soldering iron wasn't strong enough....
Some hard prints with the printer, they provide very good updates and such and show timelapses of the thing printing complicated stuff. I'm definitely getting excited for this printer, of course...
Ah okay so Aardvark, this one will work with my 24V power supply then for sure?...
Hmmm okay, well i'll give the soldering one last try. Yeah my wallet has a deep hole now, but that should be fine when it resets next week xD. Hmm smoothieware, I dunno how I feel about them, I've...
So I've pretty much had it with trying to solder the heat bed, and I know I've asked about it, but thought I make an entire new one for people who might have the same question in the future, and also...
Okay need a little help here. I'm really not too comfortable with having to mod the RAMPS 1.4 to work with the 24 Volt power supply. I'm honestly thinking since i"m overbudget and my bank account...
Yeah I did that after but the soldering iron can't reach 400 C really it's only 25 Watt which isn't enough. Yep the full kit is coming tomorrow with the flux and such, almost bought the wrong flux,...
Could you possibly link me to one? I'm just hoping my 24V 400W power supply can handle that and the system together.
Yeah I found the issue, cheap soldering iron not reaching 400C, also it's oxidized (black tip) and I didn't know how to clean it, basically improper soldering. Got a new 60W kit that'll go to 500C,...
Bed is built which I'll show later. In the meantime, I think I need to clean my soldering iron or something, it's not melting it at the tip anymore only near the middle. Hopefully this is good...
i can wait, I don't have much time to tinker really anymore, I can say almost for sure in December, but before than highly unlikely. Mind if you link to the jfriesen version?
Meanwhile, build...
I would strongly suggest octopi over Astroprint. Don't get me wrong, Astroprint works and is easier to set up than Octopi, but in my opinion, Astroprint is like Apple, in the sense that it's easy to...
yeah I decided to burn my walled even more and bought this https://www.amazon.ca/gp/product/B01N6JNFHT/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 stainless steel, will be arriving tomorrow. but...
I forgot to mention, the layer shift was happening at a different point but always the same point before I reformatted, and now it happens at a different height but same thing, so yes repeatable...
Collector's OCD xD must collect one of every type. so cartesian (corexy, Cube shaped and Cr-10 T shaped), Delta type (Normal and inverted), Scara type (RepRap Helios), Straight Line Type (the Kappa...
Wow i somehow missed your post again Trakyan so sorry xD. Yeah sure but probaly won't have time until winter holidays. since i'm busy with the Hypercube Evo right now (having small troubles), then...