I got this to work, but have gone back to Marlin for now. I attached my configuration in case someone needs a better starting point for the Makerfarm printers. Kevin was very helpful in helping me...
Type: Posts; User: PyramidDave
I got this to work, but have gone back to Marlin for now. I attached my configuration in case someone needs a better starting point for the Makerfarm printers. Kevin was very helpful in helping me...
Looks like this has a great potential for creating better prints faster and making the machine quieter. I have a Makerfarm i3v 10" with a Rambo board and have started going thru the configuration...
Interesting, he must have changed his account name. A search on Github found this link. I will have to update the link on my thingiverse pages....
Here you go. If you figure out how to convert them into some useful format like DXF, I would like to have a copy of them. Attachments are a little funny on this site & I can't tell whether it added...
I should have mentioned I did order a heat sink also. That has not arrived yet.
I tried the hair spray & used that for the 1st year, but occasionally something would lift up on a corner. I do...
Thanks. I bought this one: https://www.amazon.com/gp/product/B00HUC3PO4/ref=od_aui_detailpages00?ie=UTF8&psc=1 , but not sure when or if I will hook it up. My printer is working well with no heat...
Thanks for the info printbus. I will do some research before deciding which one to buy.
I am thinking of replacing the relay on my Makerfarm i3v 10" with a solid state relay & adding one to my FolgerTech Delta, but wanted to know how to hook it up before ordering a couple. I found...
If it is a moisture problem rather than putting it in the oven, you might try heating your 3d printer heat bed to 50 to 70C & placing the roll on the heatbed for a half hour on each side to pull the...
I am just printing PETG at 230 with no heatbed on painters tape & elmer's gluestick on Mirror from Lowes.
I have finally resolved where the problem was coming from & just finished a 2hour 47 minute print. I had not gotten past 1 hour 30 minutes before. While doing a 40 minute print this morning I heard...
I tried just changing the stepper drivers to start with. When that failed, I changed all the whole arduino Mega+Ramps. I am at a loss as to what this problem is now. The print stopped about 40...
I updated the firmware to the RCBugFix & that seems to have fixed my scale problem. Should be able to tell in a couple of hours whether the DRV8825 drivers fixed my stopping problem.
I able to print a part that takes up to about an hour and a half before it stops, so am thinking this might be a heat related problem of some sort. I am trying to swap the A4988 drivers with...
Last time I tried that, I could not get it to compile, but worked this time. Must have missed something before. Is there a standard Configuration.h file I should start with or should I do a compare...
It should not be a Windows driver problem since printing it from the SD card or from octoprint caused the same problem. I went thru & took all the connections apart & back together. I had not...
I had not thought about using a wireless SD card. That is an interesting way to print. Thanks.
What I do not understand is how I have been using it successfully for 1.5 years without this problem & all of a sudden I have a problem. If the fact that USB does not support real time protocol...
I found this ethernet shield http://www.banggood.com/Ethernet-Shield-W5100-R3-Support-PoE-For-Arduino-UNO-Mega-2560-Nano-p-907969.html Is it possible to use this instead of USB?
Using Octoprint from Raspberry Pi or connected directly to my computer using USB will give me a communication error after a short time & the printer stops. Printing directly from the SD card does...
Looks like it is the USB connection. I printed 2 prints with the SD card that were 45 minutes & 30 minutes long. I tried a 2 hour print from proterface again to see if taking all the parts off &...
I asked Colin this question also & he suggested printing from the SD card also, but thinks it might be the P/S as he has seen this similar problem before. Printing from the SD card 1st sounds like a...
I have been having a problem with my printer stopping in the middle of a print. The message I am getting with pronterface is that it has lost its connection. The heatbed & Hotend still stay at the...
There was a guy that printed the front axis for the 8" in ABS & had some problems with it cracking. Take a look at halber_mensch comments from Feb 4 & more recent here:...
I am using BuildTak on top of a Mirror. I use 230c for PETG & bed temp from 40 to 60. For PLA I am using 210c. I sometimes struggle with getting the part off the buildtak, especially really flat...