Activity Stream
-
Older Activity
-
Today, 07:53 PMCloudex la mot nen tang giao dich dang cap the gioi giup giao dich de dang va mang lai loi nhuan cao. Muc tieu cua chung toi la tro thanh noi tot...0 replies | 34 view(s)
-
Today, 04:37 PMBitcacao la nen tang de dang va an toan nhat de giao dich tai san so. Chuyen nghiep, nhanh chong va dang cap de kiem loi nhuan. Website:...0 replies | 64 view(s)
-
Today, 08:56 AMI'm a big fan of streetwear and looking to buy some new pieces from Urban Classics. Any recommendations on where to shop and compare prices?0 replies | 120 view(s)
-
Today, 04:01 AMBikeracer2020 replied to a thread Printer will print perfect calibration cube but spaghetti for everything else.. in Tips, Tricks and Tech HelpWhere you place your files on the bed in the slicer will determine where the printer prints. The 'Z' offset slicer setting is just to tune the...3 replies | 277 view(s)
-
Today, 02:42 AM3DPHRINT replied to a thread Printer will print perfect calibration cube but spaghetti for everything else.. in Tips, Tricks and Tech HelpThanks for your reply - I'll give that a go. If I'm reading this correctly, I can specify where on my printer base this actually prints?3 replies | 277 view(s)
-
Today, 12:58 AMBikeracer2020 replied to a thread Printer will print perfect calibration cube but spaghetti for everything else.. in Tips, Tricks and Tech HelpSuggestion........ Clean and level bed. Any of the free cad programs will let you draw a square 60 x 60 and just 0.2 thick (one layer thick)...3 replies | 277 view(s)
-
Yesterday, 06:34 PM3DPHRINT started a thread Printer will print perfect calibration cube but spaghetti for everything else.. in Tips, Tricks and Tech HelpHi - New to this and scrabbling about for some pointers. I have an Ender 3 Pro. After setting it all up I found a 20mm calibration cube, then I did...3 replies | 277 view(s)
-
Yesterday, 08:57 AMThe bowden tube is the plastic tube usually white PTFE, that the filament runs in from the reel to the extruder and or the hot end, and the end where...5 replies | 294 view(s)
-
Yesterday, 08:12 AMI think you could be right about it being silk PLA, I remember reading that as well. I know its not the nozzle, i replaced it recently. I do not know...5 replies | 294 view(s)
-
Yesterday, 08:06 AMSuggestions............ Bowden tube deteriorated at the hot end and not sealing properly or perhaps a partially clogged nozzle. Try a different...5 replies | 294 view(s)
-
Yesterday, 07:22 AMWith all due respect, I have tried different infill settings, up to 100 percent. This issue still crops up. Ill try 20 percent again if you need me...5 replies | 294 view(s)
-
Yesterday, 01:48 AMTry increasing infill to 20%. Hard to see what the actual print is from pic.5 replies | 294 view(s)
-
06-10-2024, 11:30 PMI bought this thing about a year ago just to stare at it seems. It's been out of the box, I powered it up like twice, manipulated the print plate,...0 replies | 299 view(s)
-
06-10-2024, 10:12 PMHi everyone,I am new to this forum, I just joined today. My name is Jared.I joined because I have an issue with my 3d printer that I cannot seem to...5 replies | 294 view(s)
-
06-10-2024, 07:34 PMHey guys. Bambu labs x1 carbon and Bambu PLA cf filament. I dried the filament before hand for 8 hours. The design I’m printing is one I made in...0 replies | 166 view(s)
-
06-09-2024, 02:07 PMJimmyJack121063 replied to a thread Printed Model of Motor Cooling Fan Breaks Apart When Operating in General 3D Printing DiscussionThanks for the info. I am having a printing service print this model in nylon for me and if that one does not hold up I will try the salt annealing...2 replies | 636 view(s)
-
06-09-2024, 10:05 AMfred_dot_u replied to a thread Printed Model of Motor Cooling Fan Breaks Apart When Operating in General 3D Printing DiscussionIt's possible that a nylon version of this fan would hold up better, but nylon can be challenging to print if you are the printing resource. As you...2 replies | 636 view(s)
-
06-08-2024, 11:22 PMHi guys, I own an Ender 3 v2 printer and have recently bought one of the Eclipson airplane models to print on it. I am printing with LW-PLA and...0 replies | 246 view(s)
-
06-08-2024, 08:54 PMJimmyJack121063 started a thread Printed Model of Motor Cooling Fan Breaks Apart When Operating in General 3D Printing DiscussionI had a model maker design an electric air compressor motor cooling fan due to the fact that I broke the original one and they are now obsolete and...2 replies | 636 view(s)
-
06-08-2024, 03:40 PMArticulated magnet: https://cults3d.com/en/3d-model/art/cat-hold-magnet0 replies | 375 view(s)
-
06-06-2024, 05:13 PMhello, do you 3dprint this table with double nozzles priter, or just it 3dprinted whole table and stick to the foil with markers? Which technique...40 replies | 170619 view(s)
-
06-06-2024, 05:09 PMHi All,anybody try to scan markers with Einscan SP? Only 3mm markers can be worked for markers? I stick 0,8mm markers, but the scanner do not...40 replies | 170619 view(s)
New member with print issue
Yesterday, 08:57 AM in Tips, Tricks and Tech Help