Close



Dig deeper, search our News website




Search:

Tag: hotend

Search: Search took 0.00 seconds.

  1. Underextrusion/skipping steps

    Started by Britin, 03-26-2019 09:04 PM
    clogging, extruder issue, hotend, skipping, underextrusion
    • Replies: 0
    • Views: 533
    Last Post: 03-26-2019 09:04 PM
    by Britin  Go to last post
  2. Ender 3 Hotend Crooked

    Started by mrmdsims, 10-27-2018 10:10 AM
    • Replies: 0
    • Views: 801
    Last Post: 10-27-2018 10:10 AM
    by mrmdsims  Go to last post
  3. heater pin numbers

    Started by ohms, 01-28-2017 01:51 PM
    cartridge, firmware, heater, hotend, pins.h
    • Replies: 4
    • Views: 5,430
    Last Post: 01-28-2017 07:17 PM
    by ohms  Go to last post
  4. change 1.75mm 3D printer to 3.0mm printer

    Started by Roy, 12-20-2016 04:11 PM
    1.75mm, filament extruder, hotend
    • Replies: 8
    • Views: 8,253
    Last Post: 12-22-2016 07:49 AM
    by noiseboy72  Go to last post
  5. converting to different filament diameter

    Started by ohms, 07-19-2016 08:42 PM
    convert, extruder, filament, hotend, modifications
    • Replies: 3
    • Views: 2,551
    Last Post: 09-13-2016 05:47 PM
    by printbus  Go to last post
  6. Hot end and stepper motor issue.

    Started by pjfossee, 01-06-2016 12:47 AM
    • Replies: 9
    • Views: 2,084
    Last Post: 01-08-2016 01:19 PM
    by printbus  Go to last post
    • Replies: 0
    • Views: 2,088
    Last Post: 12-14-2015 02:22 PM
    by RP Iron Man  Go to last post
    • Replies: 0
    • Views: 1,439
    Last Post: 12-14-2015 02:16 PM
    by RP Iron Man  Go to last post
  7. Hotend Design

    Started by Captain Hashtag, 11-09-2015 11:46 AM
    coldend, hotend
    • Replies: 3
    • Views: 1,318
    Last Post: 11-09-2015 02:19 PM
    by Davo  Go to last post
  8. Bowden oiption for E3D V6

    Started by PickyBiker, 04-03-2015 12:13 PM
    bowden, hotend, option, tube
    • Replies: 3
    • Views: 1,763
    Last Post: 04-06-2015 01:14 PM
    by PickyBiker  Go to last post
  9. Confusion

    Started by mavlock, 01-14-2015 05:36 AM
    • Replies: 2
    • Views: 1,614
    Last Post: 01-16-2015 09:36 AM
    by danrodz  Go to last post
  10. Bulldog Lite and E3Dv6

    Started by Zulfe, 11-27-2014 07:27 PM
    bulldog, e3d, extruder, hotend
    • Replies: 2
    • Views: 2,537
    Last Post: 11-27-2014 10:09 PM
    by Drone  Go to last post
    • Replies: 4
    • Views: 4,787
    Last Post: 01-05-2014 05:18 PM
    by papabur  Go to last post
Results 1 to 13 of 13