Close



Dig deeper, search our News website




Search:

Tag: problem

Page 1 of 2 1 2

Search: Search took 0.00 seconds; generated 55 minute(s) ago.

  1. einscan s temperature too high

    Started by megaprain, 04-08-2020 02:40 PM
    einscan-s scanner, high temp, problem, temperature
    • Replies: 1
    • Views: 8,309
    Last Post: 09-15-2021 03:35 AM
    by jonesdavies82  Go to last post
  2. Problem printing STL File

    Started by idarwin, 09-04-2021 12:31 PM
    • Replies: 3
    • Views: 548
    Last Post: 09-05-2021 01:25 PM
    by curious aardvark  Go to last post
  3. What’s the problem with this print?

    Started by RedAlert, 07-20-2021 07:06 AM
    • Replies: 4
    • Views: 876
    Last Post: 07-20-2021 07:54 PM
    by 3BAprinting  Go to last post
    • Replies: 4
    • Views: 5,769
    Last Post: 12-23-2020 09:36 AM
    by mistycoruscate  Go to last post
    • Replies: 4
    • Views: 1,602
    Last Post: 11-25-2020 08:38 AM
    by Robbel2005  Go to last post
  4. Strange Z - Signs on Ender 3 v2

    Started by ajaybnl, 11-09-2020 12:30 AM
    • Replies: 1
    • Views: 977
    Last Post: 11-09-2020 06:36 AM
    by Roberts_Clif  Go to last post
  5. CR10s constantly pausing

    Started by KPCx585, 10-05-2020 01:29 PM
    cr10s, cura, new to 3d, problem
    • Replies: 1
    • Views: 1,527
    Last Post: 10-06-2020 06:24 AM
    by curious aardvark  Go to last post
  6. Qidi x-max problem. Bed hieght issue.

    Started by Krillion, 03-12-2020 04:46 PM
    problem, qidi, x-max
    • Replies: 2
    • Views: 3,126
    Last Post: 03-18-2020 12:58 PM
    by Krillion  Go to last post
  7. Very strange layer height problem

    Started by suruadam, 01-14-2020 04:07 PM
    • Replies: 0
    • Views: 891
    Last Post: 01-14-2020 04:07 PM
    by suruadam  Go to last post
  8. Extruder motor not functioning on Geeetech i3

    Started by cs09, 12-13-2019 10:33 AM
    extruder, extruder motor, firmware, geeetech, problem
    • Replies: 3
    • Views: 2,955
    Last Post: 12-17-2019 05:55 AM
    by curious aardvark  Go to last post
  9. TMC2130 Layer Shifting Above ~30mm/s

    Started by CraftKing7777, 09-07-2019 08:41 PM
    • Replies: 0
    • Views: 1,222
    Last Post: 09-07-2019 08:41 PM
    by CraftKing7777  Go to last post
  10. Need help with printing quality

    Started by PZorrilla, 06-11-2019 01:09 PM
    • Replies: 6
    • Views: 3,504
    Last Post: 06-15-2019 10:17 PM
    by Rich3d  Go to last post
    • Replies: 0
    • Views: 1,535
    Last Post: 01-01-2019 10:34 PM
    by 3Dprint_everything  Go to last post
  11. Anet A8 - Gaps at circles

    Started by Jan19998, 08-24-2018 08:55 PM
    2 Pages
    1 2
    • Replies: 16
    • Views: 7,651
    Last Post: 10-06-2018 05:47 PM
    by Jan19998  Go to last post
    • Replies: 6
    • Views: 7,253
    Last Post: 08-28-2018 11:55 AM
    by Roberts_Clif  Go to last post
    • Replies: 3
    • Views: 4,057
    Last Post: 02-06-2018 05:35 PM
    by keudo  Go to last post
  12. Heating problem

    Started by lulu, 12-28-2017 03:46 PM
    heat, problem, tevo
    • Replies: 0
    • Views: 1,849
    Last Post: 12-28-2017 03:46 PM
    by lulu  Go to last post
  13. Weak Prints Problem, S.O.S

    Started by PZorrilla, 07-18-2017 07:06 PM
    fail, poor, printing, problem, weak
    • Replies: 4
    • Views: 3,108
    Last Post: 07-27-2017 06:24 AM
    by curious aardvark  Go to last post
  14. Trying to print a cylinder lying down

    Started by albert-lemeuble, 07-01-2017 11:04 AM
    • Replies: 0
    • Views: 3,382
    Last Post: 07-01-2017 11:04 AM
    by albert-lemeuble  Go to last post
    • Replies: 5
    • Views: 5,245
    Last Post: 01-18-2017 06:01 PM
    by DrBoost  Go to last post
    • Replies: 6
    • Views: 5,950
    Last Post: 12-14-2016 06:12 AM
    by wirlybird  Go to last post
    • Replies: 3
    • Views: 3,312
    Last Post: 10-18-2016 02:06 AM
    by 3dex ltd  Go to last post
  15. Heated bed problem

    Started by ryho999, 09-05-2016 01:42 PM
    fuse, heated bed, issue, not working, problem
    • Replies: 5
    • Views: 5,019
    Last Post: 09-06-2016 11:42 AM
    by printbus  Go to last post
  16. My print is warping

    Started by mrKayne, 09-02-2016 09:02 AM
    da vinci 1.0 pro, problem, warping, xyzprinting, xyzprinting davinci
    • Replies: 0
    • Views: 2,332
    Last Post: 09-02-2016 09:02 AM
    by mrKayne  Go to last post
  17. Ramps 1.4 on Wanhao I3 thermocouple reading

    Started by Goderfer, 07-12-2016 02:26 PM
    ad597, electrical noise, problem, thermocouple, wanhao i3
    • Replies: 4
    • Views: 3,846
    Last Post: 08-02-2016 09:22 PM
    by Goderfer  Go to last post
Results 1 to 25 of 47
Page 1 of 2 1 2