~ VSCode squiggles are gonna be the death of me

[Bruce19]

Hello I hope this finds a VSCode pro here. I have a Ender 3 pro whise mainboard went south. Swapped with SKR 1.4 Turbo w/ 4 TMC 2226 drivers. Ive been told I can use TMC 2209 drivers in place. ANYHOW I downloaded latest MARLIN bugfix 2.0.9 I believe. AND configurations 2.0 bugfix I followed to the T videos by Teaching Tech and Chris's basement on installing the SKR 1.4 Turbo. Ive watched both videos countless times. When I do I follow along, pause the video, make changes in fimweare, then resume video, and repeat. I have tried to tweak firmwear maybe 8 times and EVERYTIME I get the cursed squigles ~ at top of config file. Cant compile and make a *.cur file with a ~ still there. Help in Bel Air Im not adding yet the wifi or auto bed leveling yet And NOT using sensorless homing want to use end stopsI have also tried non bugfix versions of MARLIN and ConfigAt least the BTT TFT3.5 screen looks coolEnder 3 ProSKR 1.4 Turbo W/ TMC 2226 stepper drivers120v 750 watt bed heater w/ SSR300 X 300 bed (ender extender 300XL)dual Z steppers on one mainboard connection ( for now) plan on getting another Z stepper wire later

I did notice I could only download the latest VSCode v 1.65 and that the VSCode Teaching Tech and Chris was using had different line numbers when tweaking. But I KNEW to look for SAME text , it may have only been a difference of 8-20 lines


ANY FIRMWEAR GERU's OUT THERE??

[Roberts_Clif]

Tilde is its name " ~ "

Post a link to the Video I will give it a try.

[Bruce19]

sorry I dont know how to make a inet address inot one word,Teaching tech https://www.youtube.com/watch?v=-Gdk0wHg51w&t=649s and Chris's https://www.youtube.com/watch?v=oHMZ0ocTYvM

[Roberts_Clif]

VS-Code 1.65.2

I got the same error then saved all rebooted an it compiled the 2d time.

[Bruce19]

compiled second time? sucesfully ??

[Roberts_Clif]

This is a good you tube video for showing how to uploaded firmware into your 3d printer.

[Bruce19]

Ender 3 Pro
ender Extender 300XZ makes bed 300mm x 300mm and Z height 385 mm
DUAL Z steppers BUT right now ony 1 wire feeding both

I have but not yet installed
wifi
CR Touch

THANK YOU SO MUCH

[Roberts_Clif]

I followed the instructions, compiled got error could not find processor rebooted VSCode compiled perfect.

Using 7-ZIp could you zip this entire directory post on a share program like Google Drive and share the link.
Will see if I can find the error and re-post for you with comments about this error. This is to help you learn about troubleshooting software errors.

If then you still cannot see the error I will post a zip of the I created firmware.

P.S. How are you going to wire the display with ribbon cables or another way.

[Roberts_Clif]

Very good.

Now you are dangerous

I have just started enabling these lines, it makes setting the Z-Offset a thousand times simpler.

Configuration_adv.h Changes

Path:Marlin\Configuration_adv.h

#define PROBE_OFFSET_WIZARD
#define PROBE_OFFSET_WIZARD_START_Z -2.0

Enable Babystepping
#define BABYSTEPPING
#define BABYSTEP_DISPLAY_TOTAL
#define BABYSTEP_ZPROBE_OFFSET

[Bruce19]

Hello Rob Thank you so much for helping. Do you want me to send my results in zip form of vscode I got? And as far as the tft 3.5 display, Im using ribbon cables supplied