Close



Page 4 of 4 FirstFirst ... 234
Results 31 to 37 of 37

Thread: Mpcnc

  1. #31
    Engineer Roberts_Clif's Avatar
    Join Date
    Jun 2017
    Location
    Washington State, USA
    Posts
    577
    Add Roberts_Clif on Thingiverse
    Today I duplicated my DC-DC Step Down Buck Converter to my Spare Ramps 1.6 board. I am now powering both ramps with 24volt power supplies.

    Have not ordered a pair of Full Graphics controllers for my newly purchased Arduino Mega 2560 R3's and Ramps.
    Though it is still on my list of parts to be ordered.

    My next modification will be to remove the AMS1117-5.0 regulator on the Arduino and replace it with this same DC-DC Step Down Buck Converter. This time instead of setting it to a variable voltage will be using the set 5 volt jumper pin on the converter.

    This will allow for the additional power requirements needed to operate the Full Graphics controller I will be using. All power supplied from a single 24vdc power source from the Ramps 1.6 controller power pins...

  2. #32
    Engineer Roberts_Clif's Avatar
    Join Date
    Jun 2017
    Location
    Washington State, USA
    Posts
    577
    Add Roberts_Clif on Thingiverse
    Today I believe I have the Estlcam figured out I printed a more complex sketch.
    I went off the paper on the feet

    Sena.jpg

    After printing this sketch believe ready to setup a extra Stepper motor Driver for my Ramps 1.6 for the extruder.
    Will be looking a this Stepper motor Expander
    Has any one ever tried these Stepper motor expanders

  3. #33
    Engineer Roberts_Clif's Avatar
    Join Date
    Jun 2017
    Location
    Washington State, USA
    Posts
    577
    Add Roberts_Clif on Thingiverse
    Today I was wiring end-stop switches using this video on my Arduino Mega 2560 R3 an Ramps 1.6 making sure the wire were exactly the same as the video.

    Well I blew the AMS1117-05 in a heartbeat so today I replace the AMS1117-05 with a DC-DC Step Down Buck Converter 1.5V 3V 5V 9V 12V 3A Adjustable Module this was set to the 5V jumper.
    DC-DC down converter.jpg

    My question is why did this switch made by BigTree-Tech.com for maker bot kill the AMS1117-05, tested the switch it operated correctly.

    I must be right at the max current limit for the regulator because when I power it on with the new regulator is now works correctly.

  4. #34
    Super Moderator curious aardvark's Avatar
    Join Date
    Jul 2014
    Posts
    6,802
    This would be a great ideal if the MPCNC was only going to be used for 3D Printing an laser engraving.
    Though I wonder if I could keep them clean when carving wood or milling aluminum.
    well yeah, that's why you've installed a workshop vacumn and suction tubing alongside the cutting head - right :-)

  5. #35
    Engineer Roberts_Clif's Avatar
    Join Date
    Jun 2017
    Location
    Washington State, USA
    Posts
    577
    Add Roberts_Clif on Thingiverse
    Quote Originally Posted by curious aardvark View Post
    well yeah, that's why you've installed a workshop vacumn and suction tubing alongside the cutting head - right :-)
    Well actually I just ordered the Dewalt DW660 so I have quite a few more parts to be 3D Printed.

    Vacuum Duct
    Frame Supports // Frame is not as sturdy as I would like it.
    Cable chains
    Power Supply case
    Arduino, Ramps Case
    ect, ect ect.

    An forgive me but some of the thinner newly printed ABS models are quite fragile, this resemble older plastic that has degraded by weather.
    Will need to reprint them, maybe this time in PLA.

    Good thing is that the Dewalt will be showing up today and I will be able to actually be able cut something. Will start out with something weak like a piece of pink insulation.
    Then work up to some softwoods that I have laying around, and ending with hardwoods to get an ideal how fast that the cuter will work.

    At this time I have given some thought as to the size of the hot bed 400mm X 600mm will need to see if I can make it a reality Now.

  6. #36
    Super Moderator curious aardvark's Avatar
    Join Date
    Jul 2014
    Posts
    6,802
    https://www.amazon.com/Vacmaster-Gal...ateway&sr=8-11

    that would do you.

    but don't cut anything without vacumn. any kind of fine wood, metal or paper dust should not be breathed in.

  7. #37
    Engineer Roberts_Clif's Avatar
    Join Date
    Jun 2017
    Location
    Washington State, USA
    Posts
    577
    Add Roberts_Clif on Thingiverse
    Actually I have a Bucket Head Vacuum you can use any 5 gallon bucket.

Page 4 of 4 FirstFirst ... 234

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •